Design a transistor amplifier to supply a LED. The LED is required to turn on and off following the on/off signal from a digital output port of a microcomputer. The circuit is shown below. Find a suitable red LED component online and calculate the resistance values accordingly. Microprocessor output resistance RB=lk2, VoN=5V; VOFF=0V; IMAX=5mA. Transistor Vcc=5V; VBE=0.7V; B=95; VCEsat=0.2V. Rc Vcc Rg computer

Design a transistor amplifier to supply a LED. The LED is required to turn on and off following the on/off signal from a digital output port of a microcomputer. The circuit is shown below. Find a suitable red LED component online and calculate the resistance values accordingly. Microprocessor output resistance RB=lk2, VoN=5V; VOFF=0V; IMAX=5mA. Transistor Vcc=5V; VBE=0.7V; B=95; VCEsat=0.2V. Rc Vcc Rg computer

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A circuit responding to temperature is shown in figure 6. Assume the diode equation is given by Ia Ioe(qVa/kT). What is the DC operating point of the circuit at the temperature T. Also determine the small signal output swing Av, due to an incremental change in temperature AT. For this question assume Rį = 0. Heat T+AT V. DD D'B R₁ OV +AV Figure 6: Temperature sensor
3. Write down which transistor structure each curve characteristic belongs to in the figure. Ip -VGS -VGS +VGs (c) VGS (b) (a)
Given the Vth = 5V and the Rth = 650.3 ohms, what would the new output voltage be if you added a 500 ohm load resistor to the terminal demonstrated in the picture?
MOSFET Amplifier: 1. Determine the drain-to-source voltage (VDs) if VDD = +1sV and RD = 6202. The MOSFET data sheet gives and Ipss = 12 mA. (Ans: Vps=10.6 V) %3D
A 10 V Zener diode is used to regulate the voltage across a variable loadresistor. The input voltage Vs varies between 13 and16 V. The loadcurrent (??) varies between 10 and 85 mA. The minimum Zener current is15 mA. Findi. The maximum value of Rsii. The maximum power dissipated by the Zener diode, using the value ofRs.
VoO for Ma mosfet Nn Cox ( )= Jm Alv? ,Vrw=0,7V J00NA (+) VX %3D %3D a) In uhat condition does the mosfet work ?and frnd the voltage Vx= ? M1 3V b) what is the mompmum Voo voltage and why'?
I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier circuit (KBJ1008). It can be a source of any value. You don't need to do any calculations, just a drawing of how this circuit will look, please.
Figure Q6 shows the basic circuit for a Silicon Controlled Rectifier (SCR). Question 6 IĻoad V gate VP (A V Load Figure Q6 : SCR Arrangement a) Assuming the load is purely resistive : i) Sketch the load voltage waveform you would expect to see if the thyristors firing angle, a, was 30°: ii) For a secondary voltage of Vsinwt show that the average load voltage is described by : V -(1+cos(a)) Vay = 1 (27 "V sin Od0 where 0= wt 2л о You are given that Vy = iii) If the ac secondary voltage was 10Vrms and the resistive load is 202 what would be the average load current ? ||
Make a forward bias grap using the figure.
644-ELECTRONICS LAB..-5 In the half wave rectifier circuit, if the maximum output signal is 12.3 volts, what is the DC_Average for this signal? Select one: Oa. 3.92 volts Ob. 6.15 volts O c. 7.83 volts Od. 12.3 volts
What are the DC collector currents IC1 and IC2?
6-If the collector resistance is shorted,the ac output voltage will a-Decrease. b-Increase. c-Remain the same. 9 d-Equal zero. 7-If input impedance of the second stage decreases, the voltage gain of the first stage will a-Decrease. b-Increase. c-Remain the same. d-Equal zero. 8-If the load resistance of second stage opens, the voltage gain of the first stage will a-Decrease. b-Increase. c-Remain the same. d-Equal zero. 9-The feedback resistor a-Increases voltage gain. b-Reduces distortion. c-Increases collector resistance. d-Decreases input impedance. 10-when the emitter resistance Rp doubles the ac emitter resistance a-Increases. b-decreases. c-Remains the same. d-Cannot be determined. 11-To reduce the distortion in a CE amplifier, reduce the a-DC emitter current. b-Base-emitter voltage. c-Collector current. d-AC base voltage. 12-The output voltage of a CE amplifier is a-Amplified. b-Inverted. c-180° out of phase with the input. d-All of the above.