(d) Using the impedance values, Z₁ and Z2, as a basis, draw a labelled phasor diagram that quantifies the relationship between the input voltage, v;(t), and the output voltage, vo(t), at the frequency, f = 10fr. (e) Assume that the ac voltage supply, Vac, has an amplitude of 1V. Sketch a labelled time domain plot of the input voltage waveform, v;(t), and the output voltage, vo(t), at the frequency, f = 10 fr.

(d) Using the impedance values, Z₁ and Z2, as a basis, draw a labelled phasor diagram that quantifies the relationship between the input voltage, v;(t), and the output voltage, vo(t), at the frequency, f = 10fr. (e) Assume that the ac voltage supply, Vac, has an amplitude of 1V. Sketch a labelled time domain plot of the input voltage waveform, v;(t), and the output voltage, vo(t), at the frequency, f = 10 fr.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
1. Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits?. 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit?. 5. The rms value of the signal is also called the 6. The It is also the cosine of the angle of the load impedance. 7. When Q < 0, the power factor is 8. The process of increasing the power factor without altering the voltage or current to the original load is known as 9. is the cosine of the phase difference between voltage and current. is the measurement to measure average power. 10. What is the meaning of VAR?
Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits? 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit? . 5. The rms value of the signal is also called the
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
Using a line phasor (circle), draw the two given phasors. Use the sine function as the base function.
If the phasor current is 45 degrees ahead of the phasor voltage, write down all the possibilities about circuit impedance.
A series RC circuit with R=4k ohms and C= 0.40 mF is connected to an AC voltage source e(t)= 100 sin200t. Determine the following: a). The overall power factor ( indicate big leading or lagging) b). The voltage drop across the resistor and the capacitor
C1 L1 R1 V1 Vout V1 contains the fundamental and its harmonics (fo, 2fo, 3fo, ...). The amplitude of the harmonics is inversely proportional to the harmonic number. V(fo) = 10 mV V(2fo) = 10mv/2 = 5 mV V(3fo) = 10mv/3 = 3.33 mV V(4fo) = 10mv/4 = 2.55 mV a) What is the minimum value of Q for the circuit that will attenuate the third harmonic (3fo) in Vout to be less than 1% of the fundamental? b) What is the amplitude of the fifth harmonic (5fo) as a percentage of the fundamental?
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
a) Draw a sinusoidal waveform on a graph paper , assuming that Vx (effective value) and fx (kHz) are frequency. Vx= 3Volt, fx= 5Hz, Rx= 1000 *Draw the Time / div and Volt / div switches to show their positions in the screenshot where this waveform is formed and write down these locations. *Show the accuracy of the screenshot by making the necessary calculations. b) Draw a square waveform on graph paper, assuming that Vx (peak value) and fx (Hz). Vx= 3Volt , fx= 5Hz , Rx= 1000 *Draw the Time / div and Volt / div switches to show their positions in the screenshot where this waveform is formed and write down these locations. *Show the accuracy of the screenshot by making the necessary calculations. Example: Time/ Div and Volt/ Div button ms 1 5 2 16o 2 5 10 5 2 20 10 2 50 20 2 50 20 2 10 mV 10 20 CAL 5.