Current Attempt in Progress A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 34 mm, and the rod length was 380 mm. When the applied torque reached 259.8 N-m, a shear strain of 2375 microradians was measured in the specimen. What was the angle of twist in the specimen? Answer: Attempts: 0 of 1 used Submit Answer Save for Later

Current Attempt in Progress A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 34 mm, and the rod length was 380 mm. When the applied torque reached 259.8 N-m, a shear strain of 2375 microradians was measured in the specimen. What was the angle of twist in the specimen? Answer: Attempts: 0 of 1 used Submit Answer Save for Later

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Sem 2021-2022 A specimen is originally 1.5 ft long, has a diameter of o.7 in. and is subjected to a force 55olb. When the force is increased to 1900 lb, the specimen elongates o.g in. Determine the strain on the specimen and the modulus of elasticity for the material a. Strain ANSWER: in./in. b. Modulus of Elasticity ANSWER: ksi Next pag EVIOUS ACTIVITY term Quiz 1 NEXT ACTIVITY Midterm Exam >> Jump to. ype here to search
A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2% offset is 6800 kg, the yield stress will be nearly 1. 31 kg/mm² 2. 43 kg/mm² 3. 51 kg/mm² 4. 63 kg/mm² X
A hollow alloy tube 4 m long with external and internal diameters of 40 mm and 25 mm respectively was found to extend 4.8 mm under a tensile load of 60 kN. What will be the Euler's buckling load for the tube with both ends pinned?
4. The following creep data were obtained for a metal alloy tested under a constant load and at a constant temperature (the initial length of the unloaded sample was 2.0 inches): Sample Length (in) Time (hr) 2.004 2.01 100 2.02 200 2.03 400 2.045 1000 2.075 2000 2.135 4000 2.193 6000 2.23 7000 2.30 8000 (fracture) a.) Plot the strain versus time (in hours) curve for this material. b.) Determine the steady-state creep rate.
A copper rod of length L = 18.0 in. is to betwisted by torques T (see figure) until the angle ofrotation between the ends of the rod is 3.08.(a) If the allowable shear strain in the copper is0.0006 rad, what is the maximum permissiblediameter of the rod?(b) If the rod diameter is 0.5 in., what is theminimum permissible length of the rod?
The principal stresses at a point are 20 (tensile) and o (compressive), and the stress at elastic limit for the material in simple tension is 210 N/ mm². According to maximum shear strain theory, the value of oat failure is (a) 70 N/mm² (c) 140 N/mm² (b) 105 N/mm² (d) 210 N/mm²
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. Determine the lateral strain. * Your answer Determine the axial strain. Your answer Determine the Poisson's ratio v. * Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
Hi, can you answer quickly please
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 22 mm, and the rod length was 240 mm. When the applied torque reached 300.0 N-m, a shear strain of 2370 microradians was measured in the specimen. What was the angle of twist in the specimen?
A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. Calculate the required minimum diameter of the shaft: _____ mm ( input the value directly from your calculation before rounding it up to an engineering accepted diameter) Pay attention to units, and calculate your answer to one decimal place.
Q.1 The yield stresses (oy) have been measured using steel and aluminum specimens of various grain sizes, as follows: Material D (µm) σΥ (MPa) Steel 60.5 160 136 128 Aluminum 11.1 235 100 223 (a) Determine the coefficients o and kỵ in the Hall- Petch for these two materials. (b) Determine the yield stress in each material for a grain size of d=26 um.
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?