Convert 210 X 10 kJ/min to hp

Q: An oil burner nozzle is labeled 60°. This is the angle from straight ahead tothe direction that the…

A: Paper is placed 12 inches from the nozzle.  the oil burner is labeled at 600C, The Schematic of the…

Q: Hot brine from a geothermal well passes through 120 3 cm-O.D., 1 mm-wall- thickness, 16 m-long…

A: Given, The number of tubes, N = 120 The density of brine, ρ = 900 kg/m3 The bulk velcoity, u = 2 m/s…

Q: A 10mm diameter tungsten cylindrical bar should fit a 9.988mm hole contained in a steel plate.…

A:

Q: 16. What is the unit of resistance in SI? O w O W/K O m-K/W O W/m^2-K O K/W

A: Asked;  SI unit of resistance

Q: Now explore the influence of the mass of the block. Using the copper block and a 4.0 second flame,…

A: Given that, The initial temperature of 10 g block T1 = 20oC The final temperature of 10 g block T2 =…

Q: 100 lb•ft/s2 to N

A: The unit of force is to be converted from lb. ft/s2 to N.

Q: It is said that inlet gas takes 5-6 turns in Cyclone Separator.Justify the statement.

A:

Q: If the temperature profile in a rectangular slag is represented by: T(x,y,z)=x2-2y2+z²-xy+2yz…

A: The points where spacial derivatives wrt to time are 0 will be where Temperature won't change. We…

Q: A machine rotates at 8800 rpm and decelerates at 95 rad s^-2 . Find how long it takes the machine to…

A: The objective of the question is to find out the time it takes for the machine to stop from its…

Q: Convert 250 kPa to atm:

A: It is known that:

Q: A valve chokes refrigerant 134a from 0.7 mPa to 160 kpa. Determine the temperature released by the…

A:

Q: Why do some evaporators operate under vacuum? How is the vacuum produced?

A: The reason for operation of some evaporators under vacuum is to be mentioned along with the method…

Q: A 10-mm-diameter Brinell hardness indenter yielded a hardness of 350 HB when 1250-kg | s used on a…

A: ASTM E10 defines the Brinell hardness test technique, which is used to determine Brinell hardness.…

Q: na Vickers hardness testing, the average of diagonal lengths for samples A and B are reported in the…

A:

Q: A stirring rod used in the laboratory measures 12 inches. What is the length of the stirring rod…

A: length of the stirring rod in inches, l=12 inch. 1 foot=12 inch 1 yard=3 foot

Q: Answer the question below: Experiment 1: Calibration of a Calorimeter Results Time (in minutes)…

A: Before HeatingTime minutes Temperature (C)024.50.524.61.024.71.524.82.024.92.524.93.025.0Heater…

Q: Q1: Recommend the types of materials that should be used in the fabrication of a wind turbine for…

A:

Q: Enumerate the parts/components of a double-pipe heat exchanger and state their functions.

A: Components or parts of a double pipe heat exchanger are shell with nozzles, tubes, expansion joint,…

Q: Convert 50 psia (lbf/in.2 absolute) to kPa:

A: The conversion of pressure from one unit to another is to be done.

Q: Determine the work done while a body of mass 47 kg is lifted through a distance of 20 m. Also…

A: For a detailed solution, please see the attached files.

Q: In tillage operations, the typical required draft per unit width of implement for a clay soil is 5…

A: The wdth and draft width are used to obtain the total draft. The width is considered in units of…

Q: The following creep data were taken on an aluminum alloy at 48 °F) and a constant stress of 0 psi).…

A: Given -creep strain vs time data for an Al alloy at a certain stress and temperature  To find steady…

Q: Q5 Find the temperature distribution of the plate shown in figure below. Take h=k=1. 250 250 300 200…

A: When there is a temperature gradient on a plate due to hot sources of different temperatures in…

Q: Convert 1.7 x 103 Btu to kJ

A:

Q: 3 How many lbf are needed to accelerate 2 lbm at 1 ft/² ?

A: given = mass = 2 lbmacceleration = 1 ft/s2to find = how many lbf are needed

Q: what is the actual air required per hour.

A: Ultimate and proximate analysis of the coal sample is given. Flow rate of coal = 11762 kg/h % Excess…

Q: Convert 400 ft /day to cm/ sec O 13.1 O 131.1 O 1.31 O 0.131

A: It is required to convert 400 ft3/day to cm3/sec

Q: Under what conditions does a distillation column have to operate under vacuum?

A: It is to be mentioned the conditions where the distillation column requires a vacuum for the…

Q: Compare S.I and C.I engines with respect to fuel used

A: CI engine - Compression ignition engine SI engine - spark ignition engine

Q: 1. A 10.0 gram metallic alloy at 90.0 Celsius was immersed in a 40.0 g Al calorimeter which contains…

A: Given, Mass of metal alloy=10 g Mass of Al calorimeter=40 g Mass of water=80.0 g Temperature of…

Q: 10. A 6,000 lb of a material goes through a crusher and grinder per hour in succession (on the same…

A: Given that- Mass flow rate of material is,  m= 6000 lb/hr=6000 lbhr× 1hr3600 s=1.666 lb/s Rittinger…

Q: Cl the dimensions were all the same, which chocolate can withstand the greatest load? D. Which has…

A: C. The chocolate that can withstand the greatest load is to be mentioned.

Q: shear rate (/s) | shear stress (Pa) 1 86 1.8 151 168 165 8 176 10 165 15 195 25 225 44 286 60 330…

A: Write the power-law model as follows: σ = μγn Apply ln on both sides lnσ = lnμγnlnσ = lnμ + lnγnlnσ…

Q: Reynolds analogy is preferred over Chilton-Colburn analogy. O True False Depends on Sh O Only for…

A: Chilton Coulburn analogy is widely successful analogy used for estimating mass transfer…

Q: Convert 0.002 kg/ms to lbm ft s

A: