Configuration 1 Condenser accumulator Top Tray Reflux Stream Product Stream Configuration 2 Product Condenser Reflux Condenser CW Cold Crude Reflux Product Top Tray Configuration 3 Product Condenser Product Accumulator C.W Product Pump Around Section _Reflux Top Tray Pump Around Exchanger Cold Crude

Q: Which pump is an integral part of the petrochemical and edible oil factory? What are the use of this…

A: There are a lot of pumps used in petrochemical and edible oil factory like positive displacement…

Q: 5. List the relations that control the connection of pipes in parallel, and explain the two types of…

A: Introduction: Pipe Flow: In fluid mechanics, pipe flow is a sort of liquid flow inside a closed…

Q: 1. Pumps and its types 2. Pipelines 3. Tanks

A:

Q: Explain steady flow in relation to fluid mechanics.

A:

Q: Estimate the cut diameter and overall collection efficiency of a cyclone given the particle size…

A: Cut point diameter indicates the range of size of particles that can be collected in a cyclone…

Q: Following is the example of. O a. Orifice meter O b. Flow O C. Flow Pressure meter Rotameter

A: In the given image, the device contains a transparent glass tube that is placed vertically.  In this…

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: Explain flow rate in relation to fluid mechanics

A:

Q: A centrifuge bowl is spinning at a constant speed of 2000 rpm. The radius of bowl in cm needed to…

A: Given that N =2000 rpmwe have to find radius of bowl in cm when there is needed to create a force of…

Q: 3. Define the hydraulic and energy grade lines, and explain the method of calculating and drawing…

A: It is asked to define the Hydraulic grade line and energy grade line  and explain the method of…

Q: Why are Vertical flow-through beds preferred in RTO technology?

A: Regenerative Thermal oxidizers are used to remove air pollutants. The oxidizers will help in the…

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: In chemical engineering, explain the concept of multiphase flow and its significance in various…

A: Chemical engineers use the term "multiphase flow" to describe the simultaneous movement of two or…

Q: on control, with no datum features, can be applied to two or more

A:

Q: I. Liquid Properties a. Define (note: your definition must be based on the closed conduits/pipe…

A: We need to define the following based on the closed conduits /pipe flow .The terms given are : 1.…

Q: 4. List the relations that control the connection of pipes in series, and explain the principle of…

A: Introduction: Flow in pipes: In fluid mechanics, pipe flow is a sort of liquid flow inside a closed…

Q: In tillage operations, the typical required draft per unit width of implement for a clay soil is 5…

A: The wdth and draft width are used to obtain the total draft. The width is considered in units of…

Q: Explain the concept of fluid flow and its significance in chemical engineering processes.

A: The study of fluids, which includes liquids and gases, is known as fluid flow. Fluids may flow and…

Q: If I want do a certain application in the process engineering, what is the best type of pump that…

A: Classification of pump:

Q: Write a report detailing the energy balance in pumps, with illustrations, formulas, and diagrams and…

A: A pump is used to move liquids with the help of the pressure difference between one point and the…

Q: A centrifuge bowl shall separate 2 immiscible liq, SG = 1.1 & SG = 0.9  The diameter inside of the…

A: Given Data  The specific gravity of the two immiscible liquids are given  as :SG = 1.1 , Therefore,…

Q: Write about momentum transfer

A: Details about momentum transfer. Momentum transfer is a very useful concept in fluid mechanics.

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: Calculate the net force acting on the cone in Figure 4.69. Im Water 3 m Figure 4.69 System for…

A:

Q: (3) (a) Define process flow sheet or process flow diagram. (b) What does the process flow diagram…

A: (a)Process flow diagram: It is a flow sheet that shows the connections between different major…

Q: Explain briefly the concept of "steady state" and how does it affect your material balance…

A: Steady-state is the state of a system in which the properties of interest do not vary with time.

Q: an AE unit for energy

A: The specific heat capacity of a substance is the amount of energy required to raise the temperature…

Q: Criticize why this situation happens.

A:

Q: Determine the average speed for hydrogen molecules at OC. Select the correct response: 2530 m/s 3520…

A:

Q: What is cut-point diameter in a cyclone seperator and how is it related to collection efficiency?

A: Cyclonic separation is a method of removing particulates from an air, gas or liquid stream, without…

Q: Equally spaced trays are placed and provided with downspout and weirs inside the tray tower is to a.…

A: Answer:  Increase the contact between gas and liquid inside the column.

Q: What are the advantages and disadvantages of continuous, counterflow, mechanically assisted…

A: The advantages of the mechanically assisted forms of the continuous and counter-flow extractors are…

Q: What is wrong with the following distillation setup? (Select all that apply) A. The thermometer bulb…

A: Distillation is process of separation of fluid into its pure constituent.

Q: 1. You are to sketch and label at least 5 main components of the flow meter that is given to you.

A: To Do sketch and label 5 main components of flow meter Please note-We are discussing flow meter in…

Q: Discuss in detail (Diagram, Working and Application) about any one Flow measuring devices

A: The flow measuring device is the device that is inserted into the flowing fluid that produces a…

Q: Assume that the 5-in. valve with Cvmax = 500 is selected and that the pressures around the valve are…

A: The flow rate considered for the valve is gallons per minute. The rangeability parameter represents…

Q: 3. What factors should we take into account for the selection of the pipe size and design of the…

A: 1. Material: Pipe material assumes a vital part in deciding the quality and tension of compacted…

Q: Work output of an ideal Rankine cycle is equal to

A: Rankine cycle is the cycle for comparing performances of actual steam powered plants.