Compare S.I and C.I engines with respect to fuel used

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: Which pump is an integral part of the petrochemical and edible oil factory? What are the use of this…

A: There are a lot of pumps used in petrochemical and edible oil factory like positive displacement…

Q: A cast iron pipe (L=400 m, D=150 mm) is carrying 0.05m/s of water at 15 °C. Determine the loss due…

A: L= 400 m Q = 0.05 m³/s e= 0.26 D = 150 mm e/D = 0.00173 Hence, friction factor, F = 0.024

Q: 7. Determine the number of sprinkler heads required to protect an inside process area of 2000 ft².…

A:

Q: 100 lb•ft/s2 to N

A: The unit of force is to be converted from lb. ft/s2 to N.

Q: 1. Pumps and its types 2. Pipelines 3. Tanks

A:

Q: Following is the example of. O a. Orifice meter O b. Flow O C. Flow Pressure meter Rotameter

A: In the given image, the device contains a transparent glass tube that is placed vertically.  In this…

Q: B/ Define the Schmidt number, Prandtl number and Reynolds number and clear up the relation for each…

A: The Schmidt number (Sc), Prandtl number (Pr), and Reynolds number (Re) are dimensionless variables…

Q: A 10-mm-diameter Brinell hardness indenter yielded a hardness of 350 HB when 1250-kg | s used on a…

A: ASTM E10 defines the Brinell hardness test technique, which is used to determine Brinell hardness.…

Q: The centrifugal pump is most widely used in the chemical industry. Sketch the internal structure and…

A: Introduction A centrifugal pump converts rotational energy, often from a motor, to energy in a…

Q: The computed stress should be lower or equal to the allowable stress for the material to be safe in…

A:

Q: A centrifuge bowl is spinning at a constant speed of 2000 rpm. The radius of bowl in cm needed to…

A: Given that N =2000 rpmwe have to find radius of bowl in cm when there is needed to create a force of…

Q: 3. Define the hydraulic and energy grade lines, and explain the method of calculating and drawing…

A: It is asked to define the Hydraulic grade line and energy grade line  and explain the method of…

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: What is Outlet Gas Velocity in a cyclone seperator?

A: In mechanical operation, Cyclone separators are separation devices that use the principle of inertia…

Q: Determine the pressure difference between the two pipelines as shown below in the figure. Page=370…

A: Assumption:1) All the liquids are incompressible2) The effect of air column pressure is…

Q: In tillage operations, the typical required draft per unit width of implement for a clay soil is 5…

A: The wdth and draft width are used to obtain the total draft. The width is considered in units of…

Q: If I want do a certain application in the process engineering, what is the best type of pump that…

A: Classification of pump:

Q: The following creep data were taken on an aluminum alloy at 48 °F) and a constant stress of 0 psi).…

A: Given -creep strain vs time data for an Al alloy at a certain stress and temperature  To find steady…

Q: (b) The general characteristics of three oil wells selected for artificial lift as production method…

A: Table of 3 well are given.

Q: Write a report detailing the energy balance in pumps, with illustrations, formulas, and diagrams and…

A: A pump is used to move liquids with the help of the pressure difference between one point and the…

Q: We use magnetic sheets (lamination) for the core of the power transformer to: None of the choices…

A: the central iron core is developed from of a exceptionally permeable fabric made from skinny silicon…

Q: Convert 400 ft /day to cm/ sec O 13.1 O 131.1 O 1.31 O 0.131

A: It is required to convert 400 ft3/day to cm3/sec

Q: 3 - What is the energy equation used in orifice meter? 4 - Define vena-contracta?

A: Energy equations work on the principles of conservation of energy.

Q: 10. A 6,000 lb of a material goes through a crusher and grinder per hour in succession (on the same…

A: Given that- Mass flow rate of material is,  m= 6000 lb/hr=6000 lbhr× 1hr3600 s=1.666 lb/s Rittinger…

Q: A centrifuge bowl shall separate 2 immiscible liq, SG = 1.1 & SG = 0.9  The diameter inside of the…

A: Given Data  The specific gravity of the two immiscible liquids are given  as :SG = 1.1 , Therefore,…

Q: Cl the dimensions were all the same, which chocolate can withstand the greatest load? D. Which has…

A: C. The chocolate that can withstand the greatest load is to be mentioned.

Q: 2 - What is the use of orifice meter?

A: The flow of fluids is based on density, viscosity, flow rate, etc. These flow rates are measured…

Q: Calculate the net force acting on the cone in Figure 4.69. Im Water 3 m Figure 4.69 System for…

A:

Q: The strain of a component, which has a tensile modulus of 6 X 105 MPa, and subjected to a stress of…

A: The strain of the component with the given tensile modulus is to be determined.

Q: 7.) A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile…

A: Given data: Length of cylindrical rod=100mm Diameter of rod=10mm Tensile load=27500N Material is not…

Q: Based on the following data related to screen analysis: Power coal (1000 kg), 20 nd thickness of…

A:

Q: What is cut-point diameter in a cyclone seperator and how is it related to collection efficiency?

A: Cyclonic separation is a method of removing particulates from an air, gas or liquid stream, without…

Q: Two flocculator treat 1.2 m/s and remove flocs large than 0.02 mm. The settling velocity of the 0.02…

A: Given data: Volumetric flow rate = 1.2 m3/s Width of settler = 50.8 mm Angle = 45 0 Vertical height…

Q: Calculate in 16/hr and the mass flow rate For 5000 BPD API=11.5

A:

Q: A decanter to separate oil from water is needed. The oil flow is 8,500 lb/hr, and the water rate is…

A: Given:   A decanter to separate oil from water.   The mass flow rate of oil, moil = 8500 lb/h The…

Q: P= 670 kg/m3 V = Jo L %3D kg in %3D

A: