3. There is a vertical curve. The grade into the curve -3.6% and the grade out of the curve +4.4%. If the design speed is 60 mph, calculate the minimum required length for the vertical curve based on stopping sight distance (Hint: Find the stopping sight distance for the design speed of 60 mph first and then use formula in the textbook to calculate minimum length for the vertical curve).

3. There is a vertical curve. The grade into the curve -3.6% and the grade out of the curve +4.4%. If the design speed is 60 mph, calculate the minimum required length for the vertical curve based on stopping sight distance (Hint: Find the stopping sight distance for the design speed of 60 mph first and then use formula in the textbook to calculate minimum length for the vertical curve).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An existing vertical curve on a highway joins a +3.0% grade with a -3.0% grade. If the length of the curve is 250 ft, what is the maximum safe speed on this curve? What speed should be posted if 5 mph increments are used? Assume a = 11.2 ft/sec2, perception-reaction time t = 2.5 sec, and that S>L. Use g = 32.2 ft/sec2
Problem 2. A horizontal curve is being designed for a two-lane highway (12-ft lanes). The PC is at station 1200 + 50, the design speed is 70 mph, and a design superelevation of 0.08 ft/ft is to be used. Central angle of the curve is 40 degrees. (1) What is the min radius (measured to the centerline of the inside-most lane)? (2) Use the min value in your design, determine the station of PT. A = 40' e = 0.08 V = 70 mph PC = 1200150 1 +3 3131(6(vtoner) =951.88 -Simple Circular curves - reverse curtes- compound curves - spr e bus of Sogements Options curves fs=0.08 9=32.174H/S²
An equal-tangent vertical curve connects a +3.2 % and a -1.1 % grade. The PVI is at station 100+20 and elevation 950 ft and the PVT is at station 105+20. Answer the following 5 questions Question 3 to Question 7. The station of the PVC is at: sta 93+20 sta 95+20 sta 97+20 sta 99+20 sta 105+20
An equal-tangent vertical curve connects a -2.1% and a +3.6% grade. The low point of the curve is at elevation 278.9 ft. If the PVI is at elevation 275 ft, what is the design speed of the curve? Provide your answer in units of mi/h with step 5 mi/h (e.g., 15, 20, etc.). Design conservatively.
Calculate the minimum radius of horizontal curve if the minimum design speed is 80 kph, and the super elevation provided is 0.07, with skid resistance equal to 0.15.
A vertical summit curve is formed at the intersection of two gradients with a deviation angle of 0.025. Design the length of summit curve to provide a stopping sight distance for a design speed of 80 kmph. Assume the following: (i) Reaction time = 2.5 seconds (ii) Coefficient of lateral friction = 0.15 (iii) Coefficient of longitudinal friction = 0.35 (iv) Height of eye level of driver above pavement way surface = 1.4 m (v) Height of object above the pavement surface = 0.2 m
A 4.5 % grade intersects a - 2.6% grade at station 1 +990 of elevation 42.30 m. Design a vertical summit parabolic curve connecting the two tangent grades to conform with the following safe stopping sight distance specifications. Design velocity = 56 kph Height of driver's eye from the pavement = 1.37m Height of an object over the pavement ahead. 100 mm Perception-Reaction time = 3/4 seconds f = 0.13 Determine the length of the curve in m.
The degree of curve of a sample curve is 5°. Compute the desired super elevation required if the design speed of a car passing thru the curve is 80kph and the skid resistance is equal to 0.12.
Compute the difference in radius of horizontal curves with a ruling design speed of 100 kph and a minimum design speed of 84 kph. Assume super elevation and coefficient of friction for both curves to be equal, e = 0.07 and f = 0.15 respectively.
A 5% grade intersects a -3.4% grade at station 41+990 of elevation 42.30 m. Design a vertical summit parabolic curve connecting the two tangent grades to conform with the following safe stopping sight distance specifications.Design Velocity = 60 kphHeight of driver's eye from the road pavement = 1.37 mHeight of an object over the pavement ahead = 100 mm Perception-reaction time = 3/4 sCoefficient of friction between the road and the tires = 0.15
Determine the minimum length of a vertical curve in a residential street if the grades are –4% and +3%. A design speed of 10 km/h higher than the posted speed limit has been adopted for this road. Consider the most common and desirable assumptions for road design in Australia. Assume stopping sight distance for this road is higher than the length of the vertical curve. Consider passenger car to obtain the height of eye of driver and object height (car tail light). Select one: a. None b. 35 c. 64 d. 81
A rising grade of 1.5 percent meets a falling grade of 4.0 percent at station 2+400 of elevation 15.0 m. Design the vertical curve connecting the two tangent grades to conform with the following safe stopping sight distance specifications. • Design velocity = 40 mph • Height of an object over the pavement ahead = 0.11 m • Height of driver's eye from the road pavement = 1375 mm • Response-initiation time = 1.5 sec • Coefficient of friction between the road pavement and the tires = 0.10 14. Determine the stopping sight distance. a. 133.333 m b. 140.667 m c. 168.475 m d. 170.555 m 15. Determine the length of curve. a. 344.948 m b. 422.757 m c. 279.001 m d. 360.667 m 16. Determine the elevation of highest point on curve. a. 13.119 m b. 12.005 m c. 14.322 m d. 11.333 m