Consider the following statements regarding the transit mixer: 1. Their function is mainly to keep the mix in an agitated condition. 2. These mixers in addition to the outer spirals have four inner spirals. 3. A number of special nozzles provided on the lower side of inner mixing spirals, precisely and uniformly spray water on the mix under pressure along the entire length of the drum. Which of the above statement are correct? A B C 1 and 2 only 2 and 3 only 1 and 3 only D 1, 2 and 3

Consider the following statements regarding the transit mixer: 1. Their function is mainly to keep the mix in an agitated condition. 2. These mixers in addition to the outer spirals have four inner spirals. 3. A number of special nozzles provided on the lower side of inner mixing spirals, precisely and uniformly spray water on the mix under pressure along the entire length of the drum. Which of the above statement are correct? A B C 1 and 2 only 2 and 3 only 1 and 3 only D 1, 2 and 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute gage pressure at the center of pipe for solution use A. British unit B. Standard industrial unit
In the figure, in +he water 0,1M -(2) Alow in the T-shapped pipe inthe horizental plane, の3m the flow velocityinthe Ist section 1s v, 4MIS, +he relative pressure is pi = 3 kg lkm? Find the X andy components of the force that the fluid acts on the T- pipe segmant, the ossiming Alow at fluid ideal if the 2nd cross Section Vz =4mls %3D
choose the correct answer B-The main difference between the flow in pipes and the flow in open channels is * a) Existing the head loss b) Existing the free surface c) Existing the pressure drop d) None of all above
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
Probl Compute gage pressure at the center of pipe. For solution use: (a)British Unit, (b)Standard Industrial Unit? (a) + Specific gravity = 1.00 6 in 12 in 30 in Specific gravity = 2.00 (b)
The distilled water exit the desalination unit through a pipe at a rate of Qmain andpressure Pmain, branches out into two pipes at right angles, each carrying half thetotal flow, as shown in the plan view below. The diameter of the main pipe is dmainand the diameter of the two smaller pipes is dbranch. If the space ABCA is filled witha filler material, calculate the total reaction force generated by the filler to resistthe forces acting on the bends of the branching pipes.
00 F10 F11 Y F12 Scr Lk PrtS C H V DURING A TEST OF A FRANCIS WHEEL HYDRO ELECTRIC POWERPLANT, THE POWER OUTPUT IS 4 MW AND THE VELOCITY IS 7.5 H/S. THE INSIDE DIAMETER OF THE PENSTOCK IS 3 FT, LENGTH IS 350 FT AND THE ELEVATMON OF THE CENTERLINE OF THE TUR- BINE NO2ZLE IS D FEET ABOVE THE TAILRACE HEADWATER ELEVA- TION 1300 FT, FRICTION FACTOR=0.4, EXIT VELOCITY IN THE PRAFT TUBE 1.6 FT/S IF THE OVERALL EFFICIENCYIS 80%,DETERMINE: • THE TALWATER ELEVATION IN FEET. •THE PRESSURE AT THE BASE OF THE NOZZLE IN PSI. MODULE ASSIGNMENT %3D
The steel pipe shown carries water from the main pipe A to the reservoir and is 2 inch in diameter and 240 ft long. What must be the pressure in A to provide a flow of 45 gpm? Clevation K00 t Water 7 50 F Open globe valve 90 bends (threaded)- Elevtion 20 fr 2 in galvanizcd pipe
(1) ū = -2xyi i = y? – x² w = 5k K (1) V = – 2tr 2tr a-) Is the flow field given in (1) incompressible? b-) Is the flow field given in (1) irrotational? c-) Determine the vorticity for the flow field given in (II). d-) Make a sketch for the folloing fluid propeties by combining the forced and free vortex. Ve る
Fluiid mechanicx. hydraulics
Q2 (a) Differentiate between minor head loss and major head loss in a pipe system
In Single Operations, characterize the gate valve, globe valve and butterfly valve.