Consider the circular bent rod with điameter 20 mm. The free-end of the bend is subjected to loads as shown in the figure below Find all the components of stresses in section b-b. If you select wrong answers, you will have negative score in this question. 400 mm 100 mm 300 mm al 200 mm D. 400 N 800 N

Q: Consider a hollow circular shaft of inner radius r; = 1.25 inch and outer radius of ro = 1.50in,…

A: Find the state of stress at point P

Q: Determine average normal stress. Express your answer in pounds per squared inch to three significant…

A: Note: As per Expert Guidelines we are supposed to answer only the first three parts of the given…

Q: 30 MPa 20 MPa 50 MPa 50 MPa 20 MPa 30 MPa What is the radius of the Mohr's circle for the element…

A: Given, Normal stress in x direction = σx = 50 MPa Normal stress in y direction = σy = 30 MPa Shear…

Q: iven an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: Given: The shear stress acting on the element = -35 kPa The normal stress along the x-axis = 20 kPa…

Q: 40 MPa 35 MPa -60 MPa Figure 1 Due to the applied loading, the element at one point on the solid…

A:

Q: Homework: For the element shown find 1) Principle stresses and their direction 2) Shear stresses and…

A: (1) To find : The principle stress and their direction. Given data : The normal stress in X…

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Given:σx=50 MPaσy=-30 MPaζxy=20 MPa

Q: 20 MPa 100 MPa 40 MPa

A: given ; ⇒stress in x- direction (σx)=100MPa⇒stress in y-direction (σy)=20MPa⇒shear stress in x-y…

Q: The state of plane stress in a structural element is indicated by the stress element in figure B1.…

A:

Q: Question 3 Based on the diagram below a) Find the internal forces of A, B & C. 950 тm 045 тm Ø30mm F…

A: First we need to calculate the reaction from the wall by balancing all the forces.  Sum of all the…

Q: A B (1 E F (Enter only the values in the boxes by referring the unit given in bracket.) D The value…

A:

Q: b) For the given state of stress on the surface airplane fuselage as shown in Figure 4, determine…

A: given; stress in x -direction (σx)=-48MPastress in y -direction (σy)=19MPashear stress in xy plane…

Q: material is 280 MPa. Using a safety factor of 1.5, determine the material thickness of the tank in…

A:

Q: A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length…

A:

Q: QUESTION 15 Consider the circular bent rod with diameter 20 mm. The free-end of the bend is…

A:

Q: a state of stress at a point in a member defined by the element shown in the figure. Find the main…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A:

Q: 50. Consider the stress block shown in Figure 6. Determine the normal stress on AB. a. 125 kPa b.…

A: σx = 500 kpa θAB = 30°ζXY =0σY =0SO θ= 90 + 30 =120°

Q: stress element x=21Mpa, y=11Mpa, xy=8, angle=50 degrees using the arithmetic method and Moore's…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: To study the given mohr's circle and determine the given stresses.

Q: Angle 1 Oy Tyx Figure 1 Point A(-x-direction stress 60MPA(compression), y-direction stress…

A: The given values are - σx = -60MPa , σy = 40MPa, τxy = -30MPaθ = 30° The stresses on inclined plane…

Q: Question 2 For the stresses of plane stress state is ox = -8 MPa , Oy = 7 MPa and Txy = -6 MPa Draw…

A:

Q: Determine the smallest allowable cross-sectional areas of each me 400 kN The working stresses are 60…

A:

Q: Segment AB of the bar is a tube with an outer diameter of 1.5 in. and a wall thickness of 0.125 in.…

A: Given:doAB=1.5 int=0.125 indBC=0.75 in

Q: Q: The soil element with known stress conditions is shown in following figure. (i) construct Mohr's…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of…

A:

Q: The solid shaft in (Figure 1) is subjected to a torque, bending moment, and shear force. igure 300…

A:

Q: A (160+Reg. No.) kN force is applied as shown at the end of a hot-rolled steel beam. Neglecting the…

A:

Q: method is used to find stresses on an oblique plane of a member when it is subjected to stresses in…

A: OPTION (B) Mohr's circle

Q: The stress components acting on an infinitesimal element extracted from a plate subjected to the…

A: From the given figure we can observe that the principal stress formula is given by…

Q: The state of stress at a point in a structure is shown on the following element. Determine the…

A:

Q: The force F=(...) kN exerted on the bar as shown in the figure. The bar's diameter is 150mm. Find…

A:

Q: Find the Normal Stress at points A, B, and C

A: To Find the Normal Stress at points A, B, and C

Q: che principal stresses, the in-plane maximum shear stress, the prin ransformations equations resses…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.