Question 3 For the given element: A. 30 MPa 70 5 MPa 15 MPa B a) Determine the normal and shear stresses acting on the inclined plane AB shown in the figure. Show the results on a properly oriented element, indicating orientation, and all stresses. b) Using the original element (i.e. ignoring AB), determine the angle at which the shear stresses on the element will be equal to Zero. Show the results on a properly oriented element, indicating orientation, and all stresses.

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: Find the pitch for an internal thread, if the depth of thread is 0.5 mm. Pitch (in mm) =

A:

Q: The figure shows Mohr's circle for moment of inertia If each small square is 10 units what is the…

A:

Q: The state of plane strain on an element has components of Ez = 500 (10-6), y = 300(10-6), and…

A:

Q: The triple thread screw has a lead of 15 mm. Determine its thread per inch.

A: Given               Lead, L = 15 mm                           = 0.59 in No of thread, n = 3 Find…

Q: What is the solid area’s second moment about the Y-axis

A: according to the given details in the question.

Q: 3. Find the moment of inertia about X-X axis. 6 in. 0.5 in. 4 in. 0.5 in. K

A: find the moment of inertia about x-axis.

Q: 4. The diameter of a circle has endpoints: (2, -3) and (-6, 5). Can you find the coordinates of its…

A: We know that if the endpoint of diameter of circle are p(x1, y2) and q(x2, y2)  Then it's center's…

Q: please use Mohr's circle for the solution

A: Use Mohr's circle, The state of stress at a point is shown on the element. To find-  (a) The…

Q: thread the outer Jiem 10

A: Given data Outer diameter =26mm Inner diameter =18mm

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: Find the moment of inertia of the shape in the figure. 50 mm bh3 bh3 I = 12 12 25 mm ww os 25 mm

A: Given: The length of the outer rectangle is, b=50 mm. The width of the outer rectangle is, h=50 mm.…

Q: Calculate the moment of inertia of the shaded figure about its base a-a.

A:

Q: How we find the Metacentric Height using Metacentric Height Apparatus?

A:

Q: Find the moment of inertia on the side 12 The answer is within an hour

A: It can be seen that that the coordinate axes are drawn and a vertical axis also drawn parallel to…

Q: Can you please draw Mohr's circle for the solution above?

A: Given that, σx=350 MPaσy=230 MPaτxy=-480 MPa

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: How can the angle of twist of one end of a shaft or tube with respect to theother ends be…

A: Given Data: The length of the shaft is L. The diameter of the shaft is d. The moment acting on the…

Q: Draw the aligned sectional view of the following solid

A: According to the given data, there are two projection views. We need to find The sectional view as…

Q: Write the general equation of the circle of center (0, 4) and radius 4. Figure is not required.

A: The generalized equation of a circle with centre at origin and radius = r units is as given below:…

Q: The distance y from the back of the shorter leg to the neutral axis XX is

A:

Q: Determine the major diameter limits (upper and lower) for the following thread using the Machinery's…

A: Here we have given thread ½-20 UNF 2A and need to find out its  major diameter limits i.e. Upper and…

Q: The rectangular plate has a semi-circle cut out as shown. The x' and y' axes go through the centroid…

A:

Q: A cylindral drill with radius 4 cm is used to bore a hole through the center of a sphere with radius…

A: Given Data⇒Radius of cylindrical drillr1=4 cmRadius of spherer2=7 cmProblem definition⇒Problem says…

Q: Determine the centriod of the shaded area 80 mm ת 80 mm 60 mm

A: Given: square of 80 mm X 80 mm with a removed quarter circle of radius 60 mm To find: centroid…

Q: y b a a = 9 in b = 1.2 in с 3 2.4 in

A: Find the centroid distance in inches.

Q: For the shape below, calculate the second moment of area (moment of intertia) with respect to the…

A: Moment of area about x axis is 0.27*10-3 m4Explanation:Please find solution

Q: 2. Find the centroid of the figure shown. "20 in 18 in 10 in 12 in

A:

Q: * Calculate the moment at point A 1.5m 45° 5m 400 N 1848.5 N.M 1885.5 N.M 1838.5 N.M O

A: The moment at point A is 1838.5 N-m.

Q: Figure Part C Ive = tof 1 Value Part A Use Mohr's circle to determine the moment of inertia of the…

A:

Q: 250 Draw the triangle of for ces and determine the resul tant of the two forces acting in the…

A:

Q: Write the equation of the Centroid of an area?

A: The centroid of an area is the center of gravity of that particular area where the entire mass can…

Q: Find the Centroid of the composite area shown below.

A:

Q: 500 I In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R…

A: Solution:   According to the Cosine law, the Resultant of two concurrent, co-planar force system…

Q: Determine radius of mohr circle

A: