Examble 9:- Consider the circuit shown in Figure Q3. A delta-connected source supplies power to a delta-connected load through wires havingimpedances of Ziine = 1+ j2 Q. The load.impedances are ZA = 12 + j3 NThe line to line voltage Vmax is 537 V with 30:degree phase shift. Calculate the followingThe line current.(1)+12 2(ii) The line-to-line voltage at the load.V (30°+j2 Q(iii) The current in each phase of the load.(iv) The power delivered to the load.(v) The power dissipated in the line.

In this question, Find the load voltage at the load, currents in each phase, power dissipate in…

Consider the circuit shown in Figure Q3. A delta- connected source supplies power to a delta- connected load through wires having impedances of Zline = 1 + j2 N. The load .impedances are Za = 12 + j3 N The line to line voltage Vmax İs 537 V with 30 :degree phase shift. Calculate the following (). . The line current. (ii) The line-to-line voltage at the load. (iii) The current in each phase of the load.

Consider the circuit shown in Figure Q3. A delta- connected source supplies power to a delta- connected load through wires having impedances of Zline = 1 + j2 N. The load .impedances are Za = 12 + j3 N The line to line voltage Vmax İs 537 V with 30 :degree phase shift. Calculate the following (). . The line current. (ii) The line-to-line voltage at the load. (iii) The current in each phase of the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
In the 3-phase circuit in the figure, f = 2000 Hz. Find line and phase voltages and currents for the load.(in amplitude and phase).
Impedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz ac supply. Z1 =6.25 + j1.25 ohm; Z2 = 5+ j0 ohm and Z3 = 5-jXc ohm. Determine the value of capacitance of Xc such that the total curent of the circuit will be in phase with the total voltage. When is then the circuit current and power.
Three impedances (4-j6) ohm, (6+j8) ohm, and (5-j3) ohms are connected in parallel. Calculate the current in each branch when the total supply current is 20 A. Please provide its solution...its urgently needed...please.
(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZRY = 50 +j50 Q , ZYB = 150 + j0 Q and ZBR= 50 – j50 N. (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
Balanced 3-phase Delta connected voltage sources are given in the figure. Find the star-connected equivalent circuit of the voltage sources?
Q-3-) a V346.41 V b Z=0+339 Z=0+j3Q Z=0+/39 m Line V₂ R R R=1252 Star-Connected load R b-) Find the voltage drop value in the energy distribution line. c-) Find the voltage V₂ at the load ends at the end of the line. R B R R=1892 Delta-Connected load In the figure above, two balanced 3-phase delta and star-connected loads are connected in parallel to a balanced three-phase power distribution line. Delta and star connected loads are completely resistive and the resistance values per phase are 18 2 and 12 22, respectively. The phase-to-phase voltage value of the source feeding the line is 346.41 V (rms), and it is assumed that the three-phase network between the source and the load has an inductive reactance value of 3j 2 per phase. a-) Find the total current drawn from the source, active and reactive power values by selecting the Van voltage as a reference value.
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Impedances Z2 and Z3 in parallel are supply. Z1 =6.25 + j 1.25 ohm; Z2 = 5 + j0 ohm and Z3 = 5 – jXc ohm. Determine the value of capacitance of Xc such that the total current of the circuit will be in phase with the total voltage. When is then the circuit current and power. series with impedance Z1 across a 100 V, 50 Hz ac
Sketch the phasor diagram of the above circuit in terms of impedance, voltage, and the power triangle.