Consider the beam with an overhang shown in the figure.18 ftlb480ftlb9= 220BAC-10 ft-10 ft 6 ft +6 ft-(a) Determine the shear force V and bending moment M at a cross section located 18 ft from the left-handend A. Round your answers to the nearest whole.=|lblb - ft%3D(b) Find the required magnitude of load intensity q acting on the right half of member BC that will result in azero shear force on the cross section 18 ft from A. Round your answer to the nearest whole number.lbft

Support reaction : ∑MB=0RA×20-480×10×102+10-220×6×62+6=0RA=4194 lb∑FY=0RA+RB-480×10+220×6=04194…

Answered: Consider the beam with an overhang…

Engineering

Civil Engineering

Consider the beam with an overhang shown in the figure. 18 ft 480 6 - 220 B A C F10 ft 10 ft→+- 6 ft -→f- 6 ft -

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P 3 m 3 m 120 mm 50 mm 50 mm 20 mm 20 mm 150 mm N/A y The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of allow = 250 MPa and an allowable shear stress of Tallow= 100 MPa. a) Determine the distance to the neutral axis (y), second moment of area (I), and the section modulus (S) of the cross-section. b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P. c) Determine the maximum value of P such that bending failure will not occur. d) Determine the maximum value of P such that shear failure will not occur. e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
F y a What is the biggest Bending Stress? Beam is loaded the biggest bending moment is MB. Мв 3D 10 kNm a = 65 mm b = 90 mm %3D
Week 5, Question 2: Using the force method, calculate the bending moment at B for the statically indeterminate frame below. Please ignore the axial and shear deformations. Take a 12 kN and L = 5.5 m. a B EI A 2EI -3 m Calculate the bending moment at B: kN m MB 2EI m D EI E +=+ L
The internal shear force V at a certain section of a steel beam is 79 kips. If the beam has the cross section shown (assume a = 2.1 in., b₁ = 3.5 in., b₂ = 7.6 in., tw = tf = 0.6 in., d = 11.6 in.), determine: (a) the value of Q associated with point H, which is located 2.1 in. below the top surface of the flanged shape. (b) the maximum horizontal shear stress Tmax in the flanged shape. a H d
9. A single horizontal force P of magnitude 900N is applied to end D of lever ABD shown in the figure below. Knowing that portion AB of the lever has a diameter 36mm, determine a) the normal and shearing stresses on an element located at point H and having sides parallel to the x and y axes, b) the principal planes and the principal stresses at point H. 300 mm 120 mm y B H A 540 mm 36 mm P D
! Required information For the beam and loading shown, consider section n-n. It is given that P= 226 kN. P 50 mm 50 mm 150 mm n A B 50 mm 0.75 m 1.2 m 0.75 m 75 mm 75 mm 75 mm Determine the shearing stress at point b. The shearing stress at point bis MPа.
H.W.1 /The cantilever beam in Figure below has a rectangular cross section with dimension (20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (oms) in the beam. (b) Find the maximum bending stress (amar) in point B and C in the beam (c)Sketch the bending stress distribution over the cross scction on which the maximum bending stress occurs. A в 10 Ib/ft C 20 ft 60 ft
A prismatic steel beam is shown in the figure P. A C E,I L/3 2L/3 The plastic moment, M, calculated for the collapse mechanism using static method and kinematic method is 2PL (a) M, * M. 'p, kinematic 9. %3D 'p, static 2PL (b) M. = M, 9. (b) 'p, static 'p, kinematic 2PL =M, 9. (c) Mp. static NT %3D 'p, kinematic 2PL %3D (d) M M. 'p, kinematic %3D p, static
The figure shown is a cross section from the midspan of a fully restrained beam reinforced with 5- Ø25mm bars and has an effective depth of 437.5mm. if fy = 415 MPa and f'c = 25 MPa. Determine the following: Depth of the tension zone The strain at the centroid of the whole figure(centroid neglecting the reinforcement). The ultimate moment capacity of the beam. The balanced steel ratio. а. b. с. d. 90 mm BLOK 80 mm H/2 130 mm 80 mm 130 mm 80 mm 150 mm 120 mm 70 mm 150 mm 60 mm 80 mm 80 mml 100 mml 120 mm 60 mm
Determine the maximum bending moment for the beam shown below. Use a = 9 ft, b = 13 ft, c = 7 ft, and w = 15 kips/ft. The reaction forces for this beam are Ay = 90.8 kips and Dy 104.2 kips. %3D %3D В C D a b Answer: Mmax i kip-ft
Learning Goal: To solve for forces in statically indeteminate bars with axial loads The square bar shown (Figure 1) is 70 mm thick and 4.8 m long and is fixed supported at both ends. Aload directed leftward s appled at point C, as shown, La =3.02 m from the left end. The modulus of elasticity is E = 100 GPa if point C maves 8 = 0 175 mm to the left what is the applied force? When the number of reaction forces is greater than the number of equilitrium equations, the system is Express your answer with appropriate units to three significant figures. statically indeteminste Solving for the reactions requires some additional equations. These additional View Avallable Hint(s) equations come from considering compatibility relationships (1e, continuity of displacements and relationships berween displacements ana ioads). For an axially loaded member, the compatibility relationship for the deflections can be written by setting the total relative axial displacement between the ends of the member…
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.