A steel shaft is fixed at its one end as shown in figure find and maximum. G=84GPA :Total angle of rotation (1 :Shear stress at member AB (2 BC :CD 5mm 125N.m 500N.mm/mm 50mm 5mm 125mm C 125mm B 250mm A 50mm

A steel shaft is fixed at its one end as shown in figure find and maximum. G=84GPA :Total angle of rotation (1 :Shear stress at member AB (2 BC :CD 5mm 125N.m 500N.mm/mm 50mm 5mm 125mm C 125mm B 250mm A 50mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure Q3 shows the copper shaft subjected to the axial loads. Determine the displacement of end A with respect to end D. The diameters of each segment are daB = 75mm, dâc = 50mm, and dcp = 25mm. Take Ecu 3D 126GPa. (C02, СЗ, РО1, WP1) %3D 1250mm 1875mm 1500mm 10kN 30KN 5kN C 15KN 10kN A В
A flat brass bar has length L, constant thicknesst, and a rectangular cross section whose widthvaries linearly between b2 at the fixed support to b1at the free end (see figure). Assume that the taper ofthe bar is small. The bar has modulus of elasticity E.Calculate the displacements δB and δC if P = 200 kN,L = 2 m, t = 20 mm, b1 = 100 mm, b2 =115 mm,and E = 96 GPa.
Text: A beam is clamped at A. The beam is supported by a uniformly distributed load and a concentrated load as indicated on the sketch. The beam is made using the HE220A profile. The length of the beam is 4200 mm. and has a modulus of elasticity on it 2,0x105N/mm2 A) Calculate the bearing reactions of the beam for the given external load action. B) Establish moment and shear diagram for the beam for the given external load action. C) Calculate the transverse displacement of the free (cantilevered) end for the given external load action. D) Calculate the rotation of the free (cantilevered) end for the given external load action.
#6 will upvote anyone who will answer correctly. Correct decimal places please. Thanks
A portal frame shown in figure (not drawn to scale) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in the horizontal direction. The flexural rigidity. El, of each member is 106 kNm². Under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be Q P FIAT 5 m EI pole El 10 m R 50 kN
Explain
A portal frame shown in figure (not drawn to scalé) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in the horizontal direction. The flexural rigidity. El, of each member is 106 kNm². Under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be 5 m Q El El 10 m 50 kN
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
Pls box your final answe