Class Exercise: As shown in the Figure, air deflectors are used to reduce the drag on a truck. A reduction in drag coefficient from 0.78 to 0.58 was achieved when the deflectors are installed. Calculate the power saving by the installation of the deflectors at speed of 100 km/h and the projected area is 8.36 m2. p=1.2kg/m C 0.78 C0.58 24 Chapier 11

Class Exercise: As shown in the Figure, air deflectors are used to reduce the drag on a truck. A reduction in drag coefficient from 0.78 to 0.58 was achieved when the deflectors are installed. Calculate the power saving by the installation of the deflectors at speed of 100 km/h and the projected area is 8.36 m2. p=1.2kg/m C 0.78 C0.58 24 Chapier 11

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. For a wing of aspect ratio AR, having an elliptical lift distribution, the induced drag coefficient is (where CL is the lift coefficient) (b) TAR CL 2TAR (d) TAR2 (a) TAR 7. Laminar flow airfoil is used to reduce the (a) pressure drag (b) induced drag (c) skin friction drag (d) wave drag 8. Set the aerofoil your chosen angle of incidence is gives a good installed pressure distribution. (a) twelve degree (b) ten degree (c) eight degree 9. The critical Mach number for a thick airfoil will be (a) lesser than a thin airfoil. (b) greater than a thin airfoil. (c) equal to a thin airfoil. (d) cannot be related to thin airfoil 10. What is the dimension for Lift coefficient? (a) N/s (b) kg/N (c) Dimensionless
1. A sign is exposed to a 15 mph wind on a standard day. You may neglect the "legs" of the sign in all cases. Estimate the drag on the sign if (a) the sign is aligned lengthwise to the wind. (b) the sign is crosswise to the wind (wind perpendicular to the face of the sign). 3 m wind (part a) Tempe ASU Next Exit wind (part b) 1m 1m Configuration for part a. Configuration for part b. 1. (c) the sign is rotated by 90 degrees (so that it is 3 m high and 1 m wide) and the wind is parallel to the face of the sign. (d) the sign is rotated by 90 degrees (same orientation as in part c) and the sign is crosswise to the wind. 1m wind (part c) Tempe ASU 3 m Next Exit Configuration for part c.
An aeroplane has a rectangular planform wing with a span of 12 m and a chord of 2 m. The aircraft is flying at cruising speed of 62 m/s at an altitude of 3,200 m. Assume that the skin-friction drag on the wing can be approximated by the drag on a flat plate of the same dimensions at 0° incidence. Calculate the skin-friction drag and the maximum boundary layer thickness assuming (i) a completely laminar flow, and (ii) a completely turbulent flow. Assume μ = 1.63.10-5 N s/m², p = 0.89 kg/m³. Then, calculate the skin-friction drag accounting for transition at Recr= 5.105. What would the drag benefit be if transition was delayed to a Reynolds number of 106? What reduction in a propeller engine power would this imply in the cruise condition, assuming a propeller efficiency of 0.88?
The drag polar for the ASW 27B high performance sailplane is: CD = 0.01 +0.02CL2. What is its maximum lift-to-drag (L/D) ratio? 18 25 35 70
Q1: Find the boundary layer thickness (6) equation, the shear stress (to) and the coefficient of drag (C₁) if the velocity distribution in the laminar boundary layer over the face of a spillway was observed to be: u 7- (C)-()*+C)*. U Then calculate the boundary layer thickness and drag force if the air flows over a sharp edged flat plate 0.25m long and 0.5m wide at a velocity 1 m/s, take the air density 1.23 kg/m³ and the kinematic viscosity is 1.46*10-5 m/s².
Given: Asked: Solution:
1 .Water at 15 ºC flows past a 1.5 mm radius small sphere at 5 cm/s. What is most nearly the drag force in kgf of the sphere, if the sphere has a drag coefficient of 0.47
A conventional low speed aircraft had the following aerodynamic characteristics: CDo=0.020. e=1.0 (Oswald efficiency). The aircraft was flown to maintain a steady level flight and for minimum thrust required, at a lift coefficient of Cz=0.8. The numerical value of the aspect ratio of the wing is three decimal places). (in
I need the answer as soon as possible
Using FOILSIM NASA -The basic shapes are symmetrical airfoil and flat plate