Cite the relative amounts (in terms of mass fractions) of B for the following alloy: 15 wt% Sn at 100°C Type your answer in DECIMAL fraction for:

Q: Expandable pattern is used in ?

A:

Q: need help with part b i solved a prior

A: ◆ The mean effective pressure: 562.94 kPa. ◆ The indicated power developed by the engine is 4.10 kW.…

Q: how to measure cylinder taper and out of round

A: Cylinder out of Round is the difference of diameter when measured parallel to the crankshaft and…

Q: Q.6) Complete the following table: No. Part of vernier calliper 1 Main Scale Vernier Scale 3 Screw

A: The main scale reading is that to the left of the zero on the vernier scale. The vernier reading…

Q: dy = m y2 dx

A:

Q: What are the four movement that to be checked in a propeller loose blade

A: given; What are the four movement that to be checked in a propeller loose blade.

Q: Distinguish nominal diameter and gross diameter of bolt

A: Nominal diameter:Nominal diamater can be described as the pitch diameter of the thread of the…

Q: Determine the magnitude of the resultant force FR = F₁+F₂ and its direction, measured clockwise from…

A:

Q: The hydraulic cylinders is also known as

A: The hydraulic cylinder is a mechanical actuator which convert hydraulic energy  into the mechanical…

Q: The tooth height is defined by the sum of addendum and the dedendum Select one: True False

A: Tooth height in gear is defined as the radial distance between the addendum and dedendum circle of…

Q: A 29/32 icnh hole must be enlarged to 59/64 inch to insert a bushing. How much wider than the…

A: To find out how much wider the hole will be after enlargement, we need to calculate the difference…

Q: y h с b bh .1

A:

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: How are single-acting cylinders retracted?

A: To find : How are single-acting cylinders retracted?

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: What material is the piston? None of these answers are correct Steel Cast iron O Aluminum

A: Given:   To select the correct option for the material of the piston.

Q: Which of the following pressure is the highest? a. 25x10-4 Pascal b. 45 micro Pascal c. 0.03…

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: The velocity of flow increases when valve openings decreases Select one: O True O False

A: True Velocity of flow increases when valve openings decreases

Q: Identify the part not belonging to micrometer. Ratchet Clamp O Locknut Frame

A: Given :-  Identity the part not belongung to micrometer Ratchet  Clamp  Locknut Frame

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: Draw a FBD the tip to tail method please show steps

A:

Q: What is fitting mechanical

A: Fitting Process :- Assembling of various parts of the machine.

Q: What is the MMC of the bored holes?

A: Maximum Material Condition(MMC): In GD&T, the MMC is a feature which contains the maximum amount…

Q: Steps how to draw a needle of a cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: FGI and FKJ correct but incorrect afterwards.

A:

Q: What is the diameter of the groove?

A: Let us discuss given engineering drawing to find diameter of groove.

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True False

A: Grinding: It is defined as the metal cutting process that uses a grinding wheel for cutting…

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A: