Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80 In.     7.95 in.     11.25 In.     10.55 in.     6.85 in.     6.50 In.

Q: High precision in angularmeasurements can be made usinga sine bar. For using a 200 mm sinebar to…

A: Data available:Sine bar length is 200 mmL=200 mmDiameter of rolls is 35 mmd=35 mmInclined angle is…

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: what metric pipe size is approximately equivalent to a U.S. customary pipe size of 3/4"?

A: 34'' means 34 inch

Q: n an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A: For the solution refer below images.

Q: Calculate the Minimum Y distance on the drawing below: 1.000 C 2.000 Ø.995-1.000 I 6.00 0.008 MABC X…

A: given; net distance(Snet)=6tolerance in first circle(T1)=0.008net tolerance in x from both side…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: How much scrap pipe will be left if a 13-ft 6in. piece is cut out of a 20-foot length of pipe?

A: total length of pipe=20'cut piece length of pipe=13'6"

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: Draw a complete shearing force and a bending moment diagram. Show detailed calculations Use the last…

A: F=54 KNTo determine:Shear force diagramBending moment diagram

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: Apply the necessary symbology to establish the required tolerance and datum features to control the…

A:

Q: 10 mm Y 15 mm 30 mm 40 mm 10 mm 15 mm X

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: Step 1: Given: specific gravity, G=1.7 The objective is to determine: a. density of fluid in…

A: Specific gravity G = 1.7Find(1) Density ρ(2) specific weight ɣ

Q: U-CHANNEL IRON BASE motor 0 MOTOR 3.7 kW 3600 RPM +1.78 +1.32 +2.92 140 pump 0 89 +0.13 +0.97) +1.22…

A:

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A: 14 inch is the correct answer.

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: What is the aerodynamic (equivalent) diameter of an airborne spherical aluminium particle with the…

A: From the given data,material of particle is aluminum so, ρal. = 2.7 g/cm3da = here ds = 3 micro…

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: 7. How many ½ inch diameter set-screws would be required to transmit 3 horsepower at a shaft speed…

A:

Q: What will be the length of given mild steel rod after applying 100 kips force/load ?. If the…

A: Given, Force applied = P = 100 kips = 100 x 103 lb Diameter of rod = d = 0.5 in Length of rod = L =…

Q: Draw figure (3) by using circle, polyline, loft, slice and union.

A:

Q: A six inch diameter cylinder with a two inch rod pushes out its full stroke of 20 inches in 1.5…

A: Forward stroke Area : π462-22=25.13 in2 Volume : V=A×L=502.65 in3 Flow rate : Q=Vt=335.1 in3/s…

Q: in speed during bending why are you multiplying the speed during bending by 5/18

A: To answer: Why speed is being multiplied by 5/18.

Q: A nail 1/4 inch in diameter is embedded in a tire in which the gauge pressure is 28.4 psi. How much…

A:

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.