Calculate the heat supplied to the working fluid in a Rankine cycle with reheat. Assume that the working fluid is at superheated condition entering and leaving both HPT and LPT. The working fluid entering the boiler at enthalpy 384.31 kJ/kg leaves boiler at 3.5 MPa and 242.6 °C. The working fluid enters the reheater at enthalpy 2799.5 kJ/kg leaves reheater at 3.5 MPa and 242.6 °C.

Calculate the heat supplied to the working fluid in a Rankine cycle with reheat. Assume that the working fluid is at superheated condition entering and leaving both HPT and LPT. The working fluid entering the boiler at enthalpy 384.31 kJ/kg leaves boiler at 3.5 MPa and 242.6 °C. The working fluid enters the reheater at enthalpy 2799.5 kJ/kg leaves reheater at 3.5 MPa and 242.6 °C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A binary vapor cycle has mercury and water as its working fluids. If the efficiency of the mercury cycle is 32% while the steam cycle is 32.7%, compute the overall efficiency of the binary vapor cycle in %.
Figure 1 shows a steam power plant work on an ideal reheat Rankine cycle with uses water as a working fluid. The conditions at the inlet to the first turbine stage are 11 MPa, 630°C and the steam is reheated 600°C between the turbine stages at a pressure of 1.5 MPa and expands to 0.007 MPa in the low-pressure turbine. Assuming the work done to drive the boiler feedwater pump is not neglected. Sketch the Rankine cycle on the T-s diagram and for 1 kg steam determine the following: i. State the condition of the exhaust steam from high pressure turbine. ii. Work done on the boiler feedwater pump. iii. Heat supplied to the system. iv. Gross work output. V. Net work. vi. Thermal efficiency. vii. Specific steam consumption (s.s.c.). Both turbines isentropic 11 MPа, 630°С НР Т LP T WT 3 Reheat 0.007 MPa Condenser 1.5 MPa, 600°C qin Boiler qout Cooling water Boiler Feedwater 11 MPa Pump 0.007 MPa, saturated liquid WBFP Figure 1
A Carnot power cycle uses water as the working fluid. The boiler operates at a pressure of 2000 kPa and the condenser operates at 100 kPa. Saturated water enters the boiler and saturated vapor leaves the boiler. a. Calculate the heat transfer in the boiler and the condenser as well as the useful work of the cycle. b. Calculate the useful work extracted from the turbine and the work spent on the pump c. Determine the efficiency of the cycle using the definition of the Carnot cycle as well as using the definition of thermodynamic cycles d. Calculate the process efficiency of the pump and the turbine.
Water is used as the working fluid in an ideal Rankine Cycle. Steam enters the turbine at a pressure and temperature of 30 MPa and 620 deg C, respectively. The condenser pressure is 100 kPa. Determine the cycle thermal efficiency.
A steam power plant operates on an ideal regenerative Rankine cycle. Steam enters the turbineat 6 MPa and 450 o C and is condensed in the condenser at 20 kPa. Steam is extracted from theturbine at 0.6 MPa to heat the feedwater in an open feedwater heater. Water leaves thefeedwater heater as a saturated liquid. The mass flow rate of steam through the boiler is 6 kg/s. Show the cycle on a T-s diagram and determine (a) thenet work per kilogram of steam flowing through the boiler and (b) the thermal efficiency of thecycle. (c) The quality of steam leaving the turbine (d) The fraction of steam extracted from the turbine
An ideal Rankine cycle with one stage of reheat utilizes steam as working medium. Boiler pressure is 4 MPa, the boiler exit temperature is 400°C, and the condenser pressure is 10 kPa. The reheat takes place at 0.4 MPa and the steam leaves the reheater at 400°C. (Enthalpies are in KJ/kg.). Determine the thermal efficiency of the cycle. Determine also the thermal efficiency if there is no reheater. Without the reheater, the thermal efficiency is: Select one: O a. 35.29% O b. 32.95% O c. 34.51% O d. 33.15%
Please show the solution. Thank you very mmuch
An ideal Rankine cycle with one stage of reheat utilizes steam as working medium. Boiler pressure is 4 MPa, the boiler exit temperature is 400°C, and the condenser pressure is 10 kPa. The reheat takes place at 0.4 MPa and the steam leaves the reheater at 400°C. (Enthalpies are in KJ/kg.). Determine the thermal efficiency of the cycle. Determine also the thermal efficiency if there is no reheater. The thermal efficiency is: Select one: O a. 35.60% O b. 36.73% O c. 37.50% O d. 33.75%
An ideal Rankine cycle with one stage of reheat utilizes steam as working medium. Boiler pressure is 4 MPa, the boiler exit temperature is 400°C, and the condenser pressure is 10 kPa. The reheat takes place at 0.4 MPa and the steam leaves the reheater at 400°C. (Enthalpies are in KJ/kg.). Determine the thermal efficiency of the cycle. Determine also the thermal efficiency if there is no reheater. The quality at the exhaust of the low pressure turbine is: Select one: O a. 13% O b. 97% O c. 3% O d. 87%
3) An ideal Rankine cycle with superheat and reheat has steam entering the turbine at 10 MPa and 440 °C. The steam is extracted and sent to the reheater at a pressure of 1.5 MPa, and returns to the turbine at 440 °C. The condenser pressure is 20 kPa. The cycle produces 400 MW of net power. Determine (a) the qualities of steam at (i) high pressure turbine exit, and (ii) low pressure turbine exit (b) the thermal efficiency, in % (c) the rate of heat transfer, into the working fluid as it passes through the boiler, in MW (d) the rate of heat transfer, from the condensing steam as it passes through the condenser, in MW (e) the mass flow rate of the condenser cooling water, in kg/ h, if cooling water enters the condenser at 12 Cand exits at 37 C
Determine the net work output, the thermal efficiency and the mean effective pressure for the cycle.