Steam is the working fluid in an ideal Rankine cycle. Saturated vapour enters the turbine at 10 MPa and saturated liquid exits the condenser at 0.01 MPa. The net power output is 100 MW. Determine the mass flow rate of steam. Answer in kg/s. |

Steam is the working fluid in an ideal Rankine cycle. Saturated vapour enters the turbine at 10 MPa and saturated liquid exits the condenser at 0.01 MPa. The net power output is 100 MW. Determine the mass flow rate of steam. Answer in kg/s. |

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 5. Calculate the thermal efficiency of the cycle
boiler turbine condenser In an ideal reheated Rankine cycle, water vapor enters the high pressure turbine at a temperature of 400 °C and a pressure of 3 MPa and exits at a pressure of 0.8 MPa. After the water vapor is reheated to 400 °C, it enters the low pressure turbine and expands to a pressure of 10 kPa. a) Find the total amount of heat given to the water vapor (kJ/kg). b) Calculate the thermal efficiency of the cycle. c) Show the cycle in the T-s diagram.
1.) Calculate the difference between the Heat Added to the Boiler and Heat Rejected from the condenser in Hp if the feedwater is supplied at a rate of 0.74 short ton for a third of an hour at 24 hours operation. The feedwater pump pressure is 74 bar from a condenser pressure of 74 kPa. Also determine the over-all cycle efficiency if the temperature of the steam entering the turbine is 740 degrees Celsius.
In an ideal reheat-rgenerative cycle, steam enters the turbine at 6 MPaa and 400 degrees Celsius. After expansion to 1.4 MPaa steam is withdrawn and reheated to 300 degrees Celsius . Extractions for regenerative heating occur at 0.15 MPaa and 1.4 MPaa and the condenser pressure is 0.1 MPaa. Use mass flowrate of 1 kg/s. Compute for the following 1. Fractions of steam extracted 2. Turbine Work
In a Reheat Cycle, steam at 2,350 psia and 1,100°F enters the engine and expands to 260 psia at this point the steam is withdrawn and passed through a reheater. It re-enters the engine at 900°F. Expansion now occurs to the condenser pressure of 0.5 psia. For an ideal cycle, find the thermal efficiency.
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 4. Calculate the total turbine work of the cycle.
In an ideal reheat-rgenerative cycle, steam enters the turbine at 6 MPaa and 400 degrees Celsius. After expansion to 1.4 MPaa steam is withdrawn and reheated to 300 degrees Celsius . Extractions for regenerative heating occur at 0.15 MPaa and 1.4 MPaa and the condenser pressure is 0.1 MPaa. Use mass flowrate of 1 kg/s. Compute for the following 5. Heat rejected from the condenser 6. Pump work
The working fluid of an ideal Rankine cycle is steam. The turbine enterssaturated vapor at 8.0 MPa and the condenser leaves saturated liquid at the pressure of 0.008 MPa . The net power obtained is 100 MW. Determine for the cycle: d) Heat flow transferred in the condensere) Consider that cooling water passes through the condenser, in kg/ ℎ.Determine the mass flow of this refrigerant if it enters the condenser at15º C year sale at 35ºC .f) Determine the Carnot efficiency
The net work for a given reheat Rankine cycle is 80MW. Steam at 10 MPa and 500C enters the first turbine and then, the second turbine at 1.2 MPa and 500C. Saturated liquid exits the condenser at 20 kPa. Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the pump outlet, point 3 at the boiler outlet, point 4 at the reheater inlet, point 5 at the reheater outlet, and point 6 at the condenser inlet. Use 2 decimal places for the enthalpy and other energies in solving and for the final answers. For the steam quality (x) and entropy (s), use 4 decimal places in solving. For the specific volume, use 6 decimal places. IMPORTANT: USE THE STEAM TABLES FROM CENGEL'S BOOK ONLY (uploaded already in the files section). Determine the following: Enthalpy at point 2 in kJ/kg = Enthalpy at point 4 in kJ/kg = Enthalpy at point 5 in kJ/kg = Enthalpy at point 6 in kJ/kg = Thermal Efficiency in % = Heat added in kJ/kg = Heat rejected in…
An improved refrigeration system with a heat exchanger is shown in the following picture. The heat exchanger is used to superheat the vapor entering the compressor while subcooling the liquid leaving the condenser. The system uses R-134a. The evaporator operates at 15oF and the condenser operates at 100 psia. The heat exchanger provides 40oF of subcooling at the throttle valve entrance. a) Calculate the entropy generation at the throttle for the simple refrigeration cycle. Calculate also the entropy generation of the universe (throttle + surroundings) due to this operation. b) Calculate the process efficiency of the heat exchanger for the refrigeration cycle that includes the heat exchanger
Consider a steam power cycle operating according to the simple ideal Rankine cycle. Steam enter the turbine 4MPa pressure and 400oC and It condenses in the condenser at a pressure of 10 kPa. a)Calculate the thermal efficiency of the cycle. b)Draw the T-s diagram for the cycle.
1. Determine the Rankine efficiency of a condensing steam turbine operating in a Rankine cycle as follows: Steam pressure - 200 psiaSteam temperature - 1000 FExhaust pressure - 2 in Hg absoluteSteam rate - 1.5 lb/kW-hr 2. If the no. 1 problem has a thermal efficiency of 30%, how many barrels of 30 °API fuel oil will be required to produce 1000 kW-hr of power. Neglect the pump work.