Cable BB PROBLEM 1.4-8

Q: Q3: The rigid bar ABC in the Figure is pinned at B. Initially, the bar is horizontal. If the…

A: Area of cable Ac=200 mm2angle tanθ=34θ=36.869°Steel rod length L=6 m or 6000 mmAsteel=500 mm2…

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: A homogeneous 950 kg bar AB is supported at either end by a cable as shown in the figure below.…

A:

Q: A homogeneous bar AB is supported at either end by a cable as shown in the figure. Calculate the…

A: Let m be the mass of bar AB  Diameter of cables,  Db= 28 mm  Ds= 20 mm  σb= 90 MPa  σs= 120 MPa…

Q: Axial loads are applied to the solid cylindrical rods as shown. The loads P = 1500 lb, Q = 900, and…

A: Compound rods are constructed from sections of different materials, lengths and areas. They may be…

Q: Three steel plates, each 16 mm thick, are joined by two 20-mm diameter rivets as shown in the…

A: Given:16 mm thick, 20-mm diameter P = 50 kNUltimate shear stress for the rivets = 180 MPaTo…

Q: 3- For the plane truss with an inclined support shown below, solve for the nodal displacements and…

A:

Q: The polymer bar shown in the figure below has a width of b = 58 mm, a depth of d = 92 mm, and a…

A: Width of  b = 58 mmDepth of d = 92 mmHeight of h = 282 mmCompressive load of P = 120kNThe bar height…

Q: F1. The rigid bar ABC in the figure is supported by a clevis and pin at its right hand side and by…

A: Draw the free-body diagram of the beam.

Q: An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A,…

A: Calculate the reaction force as follows. Here, the tension in the wire CD is T.

Q: (5) A homogeneous 800-kg bar AB is supported at either end by a cable as shown in the figure.…

A:

Q: For the figure shown, have the following information: Bar (1) made of bronze Bar (2) made of…

A:

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm.  The…

A:

Q: 2.10-3 A flat bar of width b and thickness 1 has a hole of diameter d drilled through it (see…

A: Given data: -  The width of the bar is b. The thickness of the bar is t. The diameter of the hole…

Q: a. A member ABCD is subjected to point loads as shown in figure Task 2.b. Calculate (i) Force P…

A:

Q: A horizontal load PP is applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: For the assembly shown in Figure.(5). If the stress in the steel rod become (120+b) Mpa when the…

A:

Q: sembly consisting of two inclined bars, as shown in the figure.  The cross-sectional area of bar (1)…

A:

Q: When is Strain hardening used? How is it performed?

A: Strain hardening is used when there is a need to increase the hardness of the material. It also…

Q: A clevis-type pipe hanger supports an 8-in.-diameter pipe, as shown in Figure. The hanger rod has a…

A: Given data: W=2000 lb Need to determine the normal stress in the hanger rod, shear stress in the…

Q: A bent pipe is attached to a wall with brackets as shown. A force of F= 235 lb is applied to the end…

A: Given data:Force, F = 235 lba = 12 inb = 27 inc = 20.3 ind = 75 inh = 42.5 ing = 50 inAssume D is…

Q: A rod of weight 800kg is supported at the end using Steel and Bronze cable as shown in the figure…

A:

Q: If the capacity of each of the leg is 15kN, what is the safe value of W? 036 kN ONone of These…

A: For the given figure, it is required to determine: (a) Safe value of W, such that capacity of each…

Q: EXAMPLE: 4. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid…

A:

Q: The given system below, consisting of a rigid horizontal bar ABC and supported by three vertical…

A: Given data: -  The diameter of rod B is DB = 26 mm. The length of rod B is LB = 4400 mm. The…

Q: Figure Q1 shows a composite rod ABC attached in between two rigid walls. Part AB is a solid rod made…

A:

Q: 5 Find the stresses in members BC, BD and CE for the truss shown in the Figure. Indicate the tension…

A:

Q: 100 kN Stiff loading plate 10 cm 10 cm 10 cm 25 cm E= 200 GPa E = 200 GPa E= 70 GPa

A:

Q: 3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and…

A:

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: See the figure below. AD is a member with varying diameters. There are three axial loads applied at…

A: Given data: The magnitude of the force acting at the point B is; F1=10 lbs. The magnitude of the…

Q: PROBLEM 1 For the truss shown in Figure below. Calculate the loads in the following members. i. AC…

A: Find the force in members and stress in respective members.

Q: Problem #3. The figure below are cables ( circular section) supporting a 36 kN. Find the axial…

A:

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: Given : w = 2.25 in t = 0.375 in P = 4,800 lb d = 0.775 in   The average bearing stress produced in…

Q: The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has…

A: Given data Diameter of rivet = 12 mm Thickness of plate = 15 mm Width of plate = 100 mm a) if load =…

Q: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in…

A: Given data:- A two-story building P1=400 KN P2=720 KN L=3.75 m To find:- Internal axial force axial…

Q: Problem #1 The two vertical rods attached to the light rigid bar in the figure are identical except…

A: W=5600 lb

Q: (a) Using the Force Method of Analysis, draw the shear force and bending moment diagram for Figure…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.