Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter dh of the fillets so that the same stress occurs at the fillets. Given: p = 70 kN, D = 100 mm, df = 66 mm, r = 7.9 mm, t = 10 mm 07h

Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter dh of the fillets so that the same stress occurs at the fillets. Given: p = 70 kN, D = 100 mm, df = 66 mm, r = 7.9 mm, t = 10 mm 07h

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.18P: A prismatic bar is subjected to an axial force that produces a tensile stress ????=65 MPa and a...

See similar textbooks

Related questions

Q: A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E…

Q: Q A rigid type flange coupling are connected two shafts made of plain carbon steel. The shafts are…

A: Given Shear stress = 60 MPa Power, P = 25 kW Speed, N = 500 rpm Find Diameter, d

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction:

Q: A truck has a drag coefficient based on frontal area of CD = 0:86. The truck has a mass of 12,750 kg…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A: Given:F1=21 kipsF2=33 kipsσallow=29 ksi

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: A steady-state, steady flow adiabatic nozzle operates on air with these conditions. It has an inflow…

Q: Solve for B X A: A = 4j B = 2j + 3i - k Select the correct response: O4i +8k O4i + 12k ( 3i + 12j…

A: Calculated vector B×A.

Q: -3 ft- -3 ft- 1 ft Locate the centroid (, y) of the composite area. a) = 0.97 fty = 0.45 ft Ob) =…

Q: Calculate the heat (q) and the work (w) in Joules, which the system exchanges with the return…

A: Solution.jpg

Q: 5. For the overdamped oscillations, the displacement x(t) is expressed by the following x(t)-e-t [A…

A: Given data: x(t) = e-βt A eωt + B e-ωtWe have to find it's expression in terms of hyperbolic…

Q: The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected…

Q: A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are…

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

Q: The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1…

A: Speed of gear 1, N1=1200 rpmNumber of teeth on gear 1, T1=40Number of teeth on gear 2, T2=50Number…

Q: 1. From the truss loaded as shown, determine the stress induced on each of the members BC, BD and…

Q: A rope with two mass-less platforms at its two ends passes over a fixed pulley as shown in the…

Q: A 2600-lb car is moving at a speed of 66 mph when the brakes are fully applied, causing all four…

Q: A one-dimensional plane wall is exposed to convective and radiative conditions at x = 0. The ambient…

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Given: The length of the upper arm, L1 = 300 mm The length of the lower arm, L2 = 350 mm The mass of…

Q: 5-23 The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The…

Q: A batch of ceramic samples was tested to characterize its strength The unsorted fracture strength…

A: Given: The fracture strength (MPa) is given as follows, [623, 501.1, 571.7, 630, 676.1, 830.9,…

Q: By how much is the magnitude of 3B greater than that of A? A = 5i - 6j B = 3i+2j

A: GivenB=3i+2jA=5i-6j

Q: five-cylinder, 3.5-liter SI engine operates on a four-stroke cycle at 2500 RPM. At this condition,…

Q: 22. What is the equivalent A. 10 m B. 1.36 m Answer: head of 15 cm mercury in water? D. 16.34 m C.…

Q: Q4/A/ The tension specimen contains has original length L. -100 mm as a result of the tension its…

A: Given:Lo=100 mmLf=120 mm

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction:

Q: A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow…

Q: The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The orces…

A: Solution.jpg

Q: A tall open-topped standpipe has an inside diameter of 2870 mm and a wall thickness of 7.8 mm. The…

A: Calculated height h of water will produce circumferential stress of 13.8 Mpa. And calculated axial…

Q: 1. (a) (b) (c) Explain the difference between Griffith and Irwin's approach to determine the…

A: Ans. a) Griffith's theory for determining the critical stress for fast fracture in engineering…

Q: 1. Consider the system with 7-m(²+²6² +2²) and U-mgz where z-cr²,6-wt, by using the Lagrangian…

Q: In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final)…

Q: ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an…

A: Given:P1=8200 KPaT1=400 deg CP2=10 KPaη=0.76

Q: HW12 An aeroplane makes a complete half circle of 80 meters radius, towards the left, when flying at…

Q: An gas whose pressure, volume and temperature are 275 KN/m³, 0.09 m³ and 365 °F, respectively, has…

A: GivenP=275 kN/m2=275kPaV=0.09m3T1=365oF=458.15KT2=15oC=288KR=0.29 kJ/kgKCp=1.005kJ/kgK

Q: The new coordinates of scaled the pyramid ABCD, A(3,6,0), B(3,1,0), C(1,4,0) and D(2,3,3) by scaling…

Q: 1. A pipe of 100 mm internal diameter carries water at 20°C, which has a density of 998 kg/m³ and a…

Q: Q3: For the stresses at the point shown, find the followings: 1- The maximum shear stress. 2- The…

Q: Consider a rigid container that is initially empty, connected by a valve to a feed line of water at…

Q: Read the problem carefully and provide complete solutions with derivation of formulas (integrals and…

A: Introduction: The Brayton Cycle is a thermodynamic cycle that explains the operation of gas…

Q: Compute for A • B: A = 7i - 2j B = 7i+ 3j - 4k Select the correct response: О о O 1 unit O 49 units…

Q: HW1 A uniform disc of 220 mm in diameter has a mass of 3.5 kg. It is mounted centrally in bearings…

Q: Two solid cylindrical rods support a load of P = 19 kN as shown. Determine the axial load in rod…

Q: An airplane is traveling at 275 m/s in still air at 0 °C. If the Cp value is 1.005 kj/kgk and k=1.4,…

A: Gven: v = 275 m/s Cp = 1.005 kJ/kgK k = 1.4 T = 0 + 273 = 273 K

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

Q: 1. In crushers the major action is 2. Crystal structure consists of. 3. Sedimentation methods…

A: Solution to first three sub-parts as per our company policy.

Q: Hypothetical metal has an FCC crystal structure. If its density is 22.4 g/cm3, and atomic weight is…

Q: in the compression stroke of a gas engine the work done on the gas by the piston is 70 kJ/kg and the…

Q: An aeroplane makes a complete half circle of 75 meters radius, towards the left, when flying at 350…

A: Given Data The radius of the half circle is: R=75 m The velocity of the flying plane is: V=350…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine
the diameter dh of the fillets so that the same stress occurs at the fillets.
Given: p = 70 kN, D = 100 mm, df = 66 mm, r = 7.9 mm, t = 10 mm
SPA
T

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

,3-23 A 200-lb trap door (AD) is supported by a strut (BC) which is pin connected to the door at B (see figure). (a) Find reactions at supports A and C. (b) Find internal stress resultants N, V, and M on the trap door at 20 in. from A.
Solve the preceding problem if the axial stress in the middle region is 24,000 psi, the length is 30 in., and the modulus of elasticity is 30 × 106 psi. In part (c), assume that dmax = 0.02 in
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
Repeat the preceding problem but now find the stress state on Element A at the base. Let W%= 240 N, WL= 250 N, / = 5 mm, d = 360 mm. See the figure for the locations of clement A and all loads
A tension member constructed of an L inch angle section (see Table F-4(a) in Appendix F) is subjected to a tensile load P = 12.5 kips that acts through the point where the mid-lines of the legs intersect (see figure part a). Determine the maximum tensile stresser, in the angle section. Recompute the maximum tensile stress if two angles are used and P is applied as shown in the figure part b.
A steel bar with a diameter d = 12 mm is subjected to a tensile load P = 9.5 kN (see figure). (a) What is the maximum normal stresser smax in the bar? (b) What is the maximum shear stress tmax? (c) Draw a stress element oriented at 45° to the axis of the bar and show all stresses acting on the faces of this element. (d) Repeat part (c) for a stress element oriented at 22.5° to the axis of the bar.
A plane Frame with pin supports at A and E has a cable attached at C, which runs over a friction-less pulley at F(see figure). The cable Force is known to be 500 lb. (a) Find reactions at supports A and E. (b) Find internal stress resultants N, V, and M at point H.
An clement in plane stress is subjected to stresses a, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle 0. Now. The angle 0 is positive when count erclockwisc and negative when clockwise.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.