Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is applied to the cable (neglect the weight of the cable). a) Find the curve that defines the shape of the cable. b) Find the maximum tension force in the cable. c) Find the forces in the truss members 1, . ,5. Also, state if the members are in tension or compression. ... g = 60 N/m 100N - F, A B

Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is applied to the cable (neglect the weight of the cable). a) Find the curve that defines the shape of the cable. b) Find the maximum tension force in the cable. c) Find the forces in the truss members 1, . ,5. Also, state if the members are in tension or compression. ... g = 60 N/m 100N - F, A B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

help find the stress at segment BC, please
Determine the force in member BE of the loaded truss. The force is positive if in tension, negative if in compression. 6 kN 2 m C 6 kN E 2 m B 7 kN 2 m A 4 m
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F- 3190 N, a - 2.8 m, b - 5.6 m, 0 = 43°. B. a D b F Answers: AB - N AC - i N AD - i N BC - i N CD - i N
2
Given the Truss as shown below with load P = X N and P2 = 3X N. Using Method of Joints, determine the following if the maximum force at member CG is 62.50 N (Compression). a.) The Load P,. b.) The Load P,. c.) The Force at Member GF. В C D 2 m A E G F -1.5 m -1.5 m 1.5 m -1.5 m P1 P2 Note EXPRESS YOUR ANSWER UPTO 3 DECIMAL PLACES.
The cargo box as shown weighs W = 1200 lb. The force P = 800 lb is just sufficient to lift the box off the floor. The 2-D concurrent force system of the joint O is shown as well. Using the equilibrium equations: ∑ ???= 0 ; ∑ ???= 0, 1) Determine the tension force in the cable T;2) Determine the corresponding value of β
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
5 - In the plane truss system, whose loading condition is shown in the figure, there will be support reactions A and B, and rod forces 1,2 and 3. A is the fixed joint and B is the sliding joint. Loads on the beam P = 50 kN, All acute angles in the truss system are 45 degrees. Accordingly, S2 = ? a) 0B) 175C) 225D) 35.36E) 200
The bars AB and AC are joined by a pin at A and a horizontal cable. The vertical cable carrying the 200-kg mass is attached to the pin at A. Determine the tension in the horizontal cable. Neglect the weights of the bars 200 kg Answer: 1416 N
A.) Determine the magnitude of the tension at support B (N). Supports are pin connected B.) Determine the magnitude of the distance hD (m). Supports are pin connected
Given the Truss as shown below with load P and dimension L. Using Method of Joints, determine thefollowing:a.) The External Reaction at Point A in terms of P.b.) The External Reaction at Point E in terms of P.c.) The Force at Member BF in terms of P.
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2.