QI-The homogeneous bar ABCD shown in the Figure is supported by a cable that runs from A to B around the smooth peg at E, a vertical cable at C, and a smooth inclined surface at D. Determine the mass of the heaviest bar that can be supported if the stress in each cable is limited to 150 MPa. The area of the cable AB is 300 mm; and that of the cable at C is 35 3m 8 3m C 3m Figure P-114

QI-The homogeneous bar ABCD shown in the Figure is supported by a cable that runs from A to B around the smooth peg at E, a vertical cable at C, and a smooth inclined surface at D. Determine the mass of the heaviest bar that can be supported if the stress in each cable is limited to 150 MPa. The area of the cable AB is 300 mm; and that of the cable at C is 35 3m 8 3m C 3m Figure P-114

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

www. Wi A helical spring is fabricated by wrapping wire 3/4 in. in diameter around a forming cylinder 8 in. in diameter. Compute the number of turns required to permit an elongation of 4 in. without exceeding a shearing stress of 31 ksi. Use G = 12 x 10° psi. Use the formula: Tmaz = and d= 16PR πε3 64PR³n Gd4 + d 4R
Determine the magnitude of the pin force at A. Assume W = 845 Ib, a = 3.0 ft, b = 2.0 ft, r = 9 in. a a C В A W D Answer: A = i Ib
Calculate the normal stresses at points A and B of the bracket caused by the 30 kN force and determine which one is the compressive and tensile stress a= 38 kN
QUESTION 4) In the frame system in figure, the diameter of pin at joint B is d. The allowable shear stress and failure E 1m stress of the pin are Tal-60 MPa and Oal,z=120 MPa, respectively. Determine the required diameter d of the pin which carry safely the force P. b=100mm, 45° 2m t=40mm. P=10 kN 60° - Im 2m rod EDB rod ABC detail of joint B
Show complete solution, include fbd and formula used.
With complete Solution pls
#2 will upvote anyone who will answer
14
In the figure it is holding the BCD rod, the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to the BCD rod at point D. C pin is single acting and its diameter is 10 mm. According to this; Find the shear stress at the pin and the bedding stress on the AC rod.
Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in. a a B A W D Answer: A = i Ib
3. In the above figure, thick red lines are indicated as cables. If there is MN kN exerted force at DE. The value of tension of the three cables are the following: a. Tension at CD b. Tension at AD c. Tension at BD 3m MN N i 3m 1.5m 6m 1.5m
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-Section and a Channel (C-Section) fastened together by 16mmØ bolts, equally spaced from the center of the section, with shearing capacity t=100 MPa, for bearing os = 220 MPa for rivets in single shear and os = 280 MPa for rivets in double shear. E=200GPA for all materials. 8 KN 15 KN/m 12 KN/m 2m 3m 3m 2m Properties of T-Section Br = 180 mm Tf= 16 mm Tw = 12 mm D = 210 mm Properties of C-Section B = 105 mm T = 12 mm Tw = 12 mm D = 210 mm