Please solve both part I haven't any credit?? C The rectangular bar has a width w = 100 mm and a thickness of 75 mm. The shear stress in the plane ABof the rectangular block shown in the figure is 15 MPa when the load P is applied. Determine:to. The magnitude of the charge Pb. Normal stress in plane ABc. The maximum normal and shear stress acting on the block in any possible orientation.La barra rectangular tiene un ancho w= 100 mm y unespesor de 75 mm. El esfuerzo cortante en el plano ABde del boque rectangular mostrado en la figura es de 15MPa cuando la carga P es aplicada. Determine:a. La magnitud de la carga Pb. El esfuerzo normal en el plano ABc. El máximo esfuerzo normal y cortante queactúa sobre el bloque en cualquier posibleorientación.B. A rigid bar is supported by a pin at A and two linearly elastic wires at B and C (the wires are of the samematerial), as shown in the figure. The area of the wire at B is 100 mm2 and the area of the wire at C is 120mm2. Determine the reactions at A, B, and C caused by the applied force P = 10 kN.Una barra rigida está soportada por unpasador en A y dos alambres linealmenteelásticos en B y C (los alambres son delmismo material), como se muestra en lafigura. El área del alambre en B es de 100||mm? y el área del alambre en C es de 120mm?. Determine las reacciones en A, B y Ccausadas por la fuerza aplicada P=10 kN.1000-500 500 500

Answered: Image /qna-images/answer/c4ac5eb7-db7e-4451-93cb-f55f21736fbc.jpg

C The rectangular bar has a width w = 100 mm and a thickness of 75 mm. The shear stress in the plane AB of the rectangular block shown in the figure is 15 MPa when the load P is applied. Determine: to. The magnitude of the charge P b. Normal stress in plane AB c. The maximum normal and shear stress acting on the block in any possible orientation.

C The rectangular bar has a width w = 100 mm and a thickness of 75 mm. The shear stress in the plane AB of the rectangular block shown in the figure is 15 MPa when the load P is applied. Determine: to. The magnitude of the charge P b. Normal stress in plane AB c. The maximum normal and shear stress acting on the block in any possible orientation.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.12P: Plastic bar of diameter d = 32 mm is compressed in a testing device by a Force P = 190 N that is...

See similar textbooks

Similar questions

Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A cube of cast iron with sides of length a = 4.0 in. (see figure) is tested in a laboratory under triaxialsire.ss. Gages mounted on the testing machine show that the compressive strains in the material arc a = -225 X l06and,ay = 37.5 X l0_. Determine the following quantities: (a) the norm al stresses i. r,.. and acting on the x, y, and z faces of the cube; (b) the maximum shear stress r in the material; (C) the change ..W in the volume of the cube: (d) the strain energy U stored in the cube; (e) the maximum value of s when the change in volume must be limited to O.O28%; and (f) the required value of when the strain energy must be 38 in.-lb. (Assume £ = 14,000 ksi and v = 0.25.)
Solve the preceding problem if the normal and shear stresses acting on element B are 56 MPa, 17 MPa, and 27 MPa (in the directions shown in the figure) and the angle is 40° (clockwise).
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
Through 7.4-25 An clement in plane stress is subjected to stresses x,y, and r. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.422x=29.5,y=29.5MPa,xy=27MPa
through 7.4-25 An clement in plane stress is subjected to stresses sx,??y,and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of crv = —45 MPa and rTb = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element.
An clement in plane stress is subjected to stresses a,. cry, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle ??. Now. The angle 0 is positive when count ere clockwise and negative when clockwise. r
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
An clement in plane stress is subjected to stresses a,. cry, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis.