In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 Xc = 600 n 80 sin (ut + /2) X, = 600 2 0.2 sin wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source

In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 Xc = 600 n 80 sin (ut + /2) X, = 600 2 0.2 sin wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7MCQ

See similar textbooks

Similar questions

A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
One side of a transformer has What is the voltage (in V rms) at the secondary? 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low What is the current (in A rms) at the secondary? What is the current (in A rms) out of the source? What is the value of the load impedance when referred to the primary? • Referred impedance = voltage side (secondary) is connected to an impedance ZL = 20 + j10 Q. Provide at least 4 digits after the decimal point. +j_ N What is the value of the source voltage (in V rms) when referred to the secondary?
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
Which of the following statements is/are true? (A In purely inductive circuit, the current leads voltage. (B) In purely resistive circuit, the current lags voltage. C In purely resistive circuit, the current is in phase with voltage. D In purely capacitive circuit, the voltage lags current.
Section [Section Upload answer sheets Find the following parameters of an ac voltage given by the equation v-100sin370t.Find RMS value,form factor, peak factor, average value and frequency. E Submission
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit
QUESTION 1 Two magnetically-connected circuits have the following characteristics: . A series-opposing connection of coils (dot convention). The primary side is connected to a voltage source that has a magnitude of 230 V and a phase angle of 45 degrees. . The primary-side inductive reactance is jXL1 - j8 Ohm. . The secondary side is connected to a resistive load of 10 Ohm. . The secondary side inductive reactance is jXL1 =j5 Ohm. . The mutual inductive reactance is jM=j1 Ohm. The magnitude of the voltage across the resistive load is:
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Which of the following statements is/are true? A In purely resistive circuit, the current lags voltage. (B In purely capacitive circuit, the voltage lags current. In purely resistive circuit, the current is in phase with voltage. D In purely inductive circuit, the current leads voltage.