• Consider a beam of rectangular cross-section (h×b) and length L. The beam is loaded by force T = 50 N at the free end. Find the maximal normal stress o and shear stress t along the glue connection and the point(s) where they occur. L b a Glue connection

• Consider a beam of rectangular cross-section (h×b) and length L. The beam is loaded by force T = 50 N at the free end. Find the maximal normal stress o and shear stress t along the glue connection and the point(s) where they occur. L b a Glue connection

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stresses on an element are o, = -270 psi and o, = -540 psi. y Oy Find the maximum shear stresses (in psi) on the element. (Assume t. = 0. Use the sign convention for shear stresses.) ху (Tmax)x1 = psi (Tmaxlyı = psi (Tmaxl21 = psi
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is +910 uɛ. Determine the axial strain in rod (2). (1) 2,000 mm 520 mm 400 mm 1,250 mm (2)
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
Please solve it ASAP and with all the steps and please solve it urgently and please solve all the parts as well please The strains at a point in a plate subjected to plain stress were measured as: Use this information to find the stresses in an element at the same location that is rotated 30 degrees counterclockwise and draw your results.
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
The stresses acting on an element are dx = 745 psi, ay = 615 psi, and Txy = 430 psi. (Consider only the in-plane stresses the stresses in the x-y-plane). Oy Determine the principal stresses (in psi) and angle of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention. For maximum shear stress, enter the magnitude.) %1 = psi 0₂ = psi psi max = 8p = Show the stresses on a sketch of a properly oriented element. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen This answer has not been graded yet.
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X
The rod and the tube are of the same initial length and must remain together then the strain in each part must be the same. A compound bar is made up of a rod of an area A1 and modulus of elasticity E1, and a tube of equal length of A2 and modulus of elasticity E2. If a compressive load P is applied to the compound bar, find how the load is shared. The total load carried is P and let if be shared W1 and W2