Based on the information in the graph, to design a network addressing scheme to supply the minimum number of hosts per subnet, for the "Science lab", what is the network to use? IP Address 135.126.0.0 SO/0/0 FO/O So/0/1 FO/1 FO/O SO0/0 Tech Ed Lab 20 Hosts FO/1 Science Lab 10 Hosts English Department 15 Hosts Select one: O a. 196.168.6.0/28 O b. 10.0.0.0/24 O c. 127.0.0.0/26 O d. 127.0.0.0/28

Based on the information in the graph, to design a network addressing scheme to supply the minimum number of hosts per subnet, for the "Science lab", what is the network to use? IP Address 135.126.0.0 SO/0/0 FO/O So/0/1 FO/1 FO/O SO0/0 Tech Ed Lab 20 Hosts FO/1 Science Lab 10 Hosts English Department 15 Hosts Select one: O a. 196.168.6.0/28 O b. 10.0.0.0/24 O c. 127.0.0.0/26 O d. 127.0.0.0/28

A+ Guide to Hardware (Standalone Book) (MindTap Course List)

9th Edition

ISBN:9781305266452

Author:Jean Andrews

Publisher:Jean Andrews

Chapter8: Connecting To And Setting Up A Network

Section: Chapter Questions

Problem 5RB

See similar textbooks

Similar questions

An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?
An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most signi cant bits are used as a network ID, and the 16 least signi cant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?
Design a classfull network addressing scheme that will supply the minimum number of hosts per subnet, and allow enough extra subnets and hosts for 25% growth in all areas. IP Address 172.16.0.0 FO/O S//0/1 FO/O Sales Administrative FO/1 185 Hosts 30 Hosts SO/0/0 Marketing 50 Hosts,
Design a classfull network addressing scheme that will supply the minimum number of hosts per subnet, and allow enough extra subnets and hosts for 25% growth in all areas. IP Address 172.16.0.0 FO/0 S/0/1 FO/O Sales Administrative Router A FO/1 SO/0/0 185 Hosts 30 Hosts Marketing 50 Hosts
• IPV6 addresses use 128 bits to represent an address which includes bits to be used for subnetting. The second half of the address (least significant 64 bits) is always used for hosts only. Therefore, there is no compromise if we subnet the network. Use the Figure below to Create five subnets using route prefix 2001:db:acad::/48 (1 Marks) Routing Prefix Subnet ID Interface ID 48 Bits 16 Bits 64 Bits
In the Internet of Things (IoT) web stack, what function do the protocols UDP and IPV6 serve? What exactly is the difference between a sensor having a static IP address and one that has a dynamically assigned IP address?
Based on the information in the graph, we need to design a network addressing scheme that will supply the minimum number of hosts per subnet. For the WAN, between the 2 routers, the best mask to use is IP Address 172.16.0.0 FO/O S0/0/0 S0/0/1 F0/1 PERSAL Marketing 24 Hosts Management 15 Hosts Select one: O a. 255.255.255.192 O b. 256.256.256.128 O c. 255.255.255.248 O d. 255.255.255.252 O e. 255.255.255.128 FO/O MERAL Reasearch 60 Hosts
Given CS=3000H, DS=5000H, SS=7000H, ES=9000H, BX=ABCDH, SI=DCBAH, DI=FEDCH, BP=89ABH, SP=4567H, IP=789AH, what is the physical address of destination for MOVS NCT a. 5FEDCH b. 9DCBAH c. 5DCBAH d. 9FEDCH
An ISP allocates the 3000:FACE:6/48 block of IPV6 addresses to an enterprise. The entrprise assigns a the subnet id = 2B with an interface id = 2. Using the 3+1+4 address rule, what is the most compressed IPV6 representation of the address? 3000:FACE:6:2:2B/64 3000:FACE:6:0:2:2B/64 3000:FACE:6:2000::2B/64 3000:FACE:6:2:2B/64
The original HTTP protocol used TCP/IP as the underlying network protocol. For each page, graphic, or applet, a separate TCP session was constructed, used, and torn down. Because of the overhead of building and destroying TCP/IP connections, performance problems resulted from this implementation method. Would using UDP rather than TCP be a good alternative? What other changes could you make to improve HTTP performance?
You are hired to design and manage a network of a company. The topology of the network is shown above. The Internet Service Provider (ISP) provides the following information to connect the corporate network to the Internet. The CIDR range given for the company: 124.34.52.0/21 The address of the ISP router (also called "Gateway address"): 124.34.63.254 Configure the network by giving CIDR blocks for each company subnet and IP addresses for each station and router knowing that: For Ethernet 1, we need 514 hosts to connect. For Ethernet 2 we need 50 hosts to connect. For Ethernet 3 we need 123 hosts to connect. For the Token Ring network we need 132 hosts to connect. You need to take into account the gateway addresses that need to be allocated for each of the subnets. Assign IP addresses to hosts A, B, C and D and IP addresses to the router gateway interfaces. DON'T FORGET TO FILL-IN THE BLANKS BELOW. Computer B Internet Ethernet 1 Computer C Computer A Ethernet 2 Router 1 Token Ring 1…
Draw a network design that you think will be useful in the future for the industry that you have visited. Network should include the following requirements: 3 routers 4 switches 10 PCs 4 VLANs. Suitable IP addressing scheme in tabular form (assume as many hosts as necessary for each department). Indicate where do you use static routing, dynamic routing protocols (name the protocols, RIP, EIGRP, OSPF, etc.), Access Control List (ACL) as per the network preferences. Justify your choices.