b) The diode is to be used in the AND logic circuit shown in figure Q1b : VDD V, Va Ve 0 0 0 1 1 0 11l Case 1 Case 3 VA H V. L-0 Case 2 Figure Q1b : Diode - Resistor AND Gate The inputs are assumed to be at rail values where a logic High, '1', is VoD = 5V, and a logic Low, 'O', is OV. Referring to the above truth table : i) What will the output voltage V, in case 1? ii) Evaluate the value of the resistor R required to make the threshold voltage for Vo be 1V when operating in case 2. iii) Using this value of R evaluate Vo for case 3. See the Q1 solutions page at the end of the paper

b) The diode is to be used in the AND logic circuit shown in figure Q1b : VDD V, Va Ve 0 0 0 1 1 0 11l Case 1 Case 3 VA H V. L-0 Case 2 Figure Q1b : Diode - Resistor AND Gate The inputs are assumed to be at rail values where a logic High, '1', is VoD = 5V, and a logic Low, 'O', is OV. Referring to the above truth table : i) What will the output voltage V, in case 1? ii) Evaluate the value of the resistor R required to make the threshold voltage for Vo be 1V when operating in case 2. iii) Using this value of R evaluate Vo for case 3. See the Q1 solutions page at the end of the paper

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a digital logic circuit with two diodes as shown in Figure 1. The diodes, Dị and D2, are ideal (i.e., large signal diode models with V, = 0). 10 D o Vout V2 10 D2 5V 50kn Figure 1 A digital logic circuit with two ideal diodes A. Complete the equivalent circuit below and determine the output voltage vout when vị = v2 = ov. 1Ω D O Vout 12 D2 5V 50k2
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
What is the maximum current rating that each diode should have in the logic circuit shown below? Assume that the voltage drop across the silicon diode is 0.7V when it conducts. D1 Vo 1N4001 D2 R 1000 Vcc-+5V
Use your reasoning logic to determine which diodes are on and which might be off in the following circuit, assuming the diode drops are 0.7 V. A. VA B. VB C(ID1) D(ID2) E(ID3)
For the circuit shown in the following figure, Show the state of each transistor and diodes for all the possible inputs. Use a table to write your answer and Find the logical function of the circuit.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Q3: The figure below includes a bridge full-wave rectifier circuit with a diode type is1N4007. The input voltage is Vin V2 120 sin 2n60t 5:1 D3 D1 120 V RL Vp(out) D2 DA 10 kN a) Draw the output voltage waveform for the circuit in the figure and include thevoltage values. b) What is the peak inverse voltage (PIV) across each diode? c) Determine the rms voltage, current and power delivered to RL d) Determine the average voltage, current, and power delivered to RL e) What is the ratio of Po(de) to Po(ac)? lll
Please indicate the temperatures that these p-type semiconductors (Si) are at. (The circles represent holes.) [Select] V [Select] T [Select] [Select] zero Kelvin intermediate temperatures any temperature room temperature
2. What is the maximum current rating that each diode should have in the logic circuit shown below? Assume that the voltage drop across the silicon diode is 0.7V when it conducts. D1 Vo 1N4001 D2 ER 1000 Vcc-+5V
4.) In which mode will a diode generally not conduct electricity? a. Bidirectional Biased b. None of these c. Forward Biased d. Reversed Biased 5.) Consider the following schematic symbol of a semiconductor device: Which side is the Cathode? (Picture inserted down below) a. Side A b. Both side A and B c. Side B d. Neither side A or B 8.) Integrated circuits can be broken down into three basic categories. Which category does an operational amplifier (or op-amp) fall into? a. Analog b. None of these c. A combination of analog and digital d. Digital
Explain how you could measure the ripple frequency to determine if a diode were open in a bridge rectifier circuit. (own words)
Determine the a.c. ripple voltage across the load of full wave rectifier which delivers 40 W to a load resistance of 150 ohm, and ripple factor is given as 1% A) 77.4 V B) 38.7 V C) 0.387 V D) 0.774 V