(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of VwinaTunnet = 50 m/s. The measured downforce at this speed is Foownforce.wT = 3000 N and the model reference area is Aref.wT = 0.5 m². 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g 9.81 m/s. Downforce Weight

(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of VwinaTunnet = 50 m/s. The measured downforce at this speed is Foownforce.wT = 3000 N and the model reference area is Aref.wT = 0.5 m². 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g 9.81 m/s. Downforce Weight

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A laboratory study models the flow around the pier of an off-shore wind turbine with a scaled model of Lr = 20. Determine the model velocity (VM) past the pier, if the water travels with V = 2.2 km/h past the prototype pier. You can assume that water with the same fluid properties is used in both model and prototype with density of Pw = 1005 kg/m³ and dynamic viscosity of nw = 0.001 Pas. HINT: the flow around the pier is described by the Reynolds number. VM m/s (Provide your answer to 3 decimal places)
A model of the Airbus 320 is tested in a wind tunnel using air at standard conditions. If the tunnel airspeed is 50m/s, calculate the water speed if the same model is to be tested in a water tunnel atdynamically similar conditions. Take mair=1.73 x 10-5Pa.s, mwater=10-3Pa.s, rair=1.225kg/m3 andrwater=1000 kg/m3.
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
A particle of mass m moves in a straight line wih velocity v(t), subject only to a linear air resistance F = -1mv. Assume the particle starts with velocity u in x = 0. dv 1. Using the change of variables = V- dt v(x) = du, find the velocity of the particle as a function of its position, a, the initial velocity, u, and its mass, m. dx 2. Calculate the distance travelled by the particle before coming to a stop. ΕΠΙΣ î=
A jet engine on a test stand directs a stream of hot exhaust gasses against a vemcal wall. All of the exhaust gas leaving the wall after impact is in the y-z plane (ie no "x" direction velocity). The mass rate is 200 kg/s and the velocity is 400 m/s. (Note that the density and viscosity are not relevant) What is the force on the wall (include direction)?
(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration
Q1: If an air stream flowing at velocity (U) pasta body of length (L) causes a drag force (F) on the body which depends only upon U, L, and fluid viscosity μ. Formulate the suitable dimensionless parameter of the air drag force.
1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.7 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. 1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 665150 cm³ and weight of 71 kN (ENTER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) 1 (a) The dynamic viscosity of the fluid (in Centipoise) The kinematic viscosity of the fluid (in stokes) 1 (b) Specific Weight in (kN/m3) Density of liquid (in kg/m2) Specific gravity of liquid Windows bu
Answer all the questions 1) Using dimensional equations, convert: 700 m* /(day. kg) to cem* /(min. g). 2) Convert 210 X 10 kJ/min to hp 3) Calculate the weight in lbr of a 30.0-lbm object. 4) Calculate the mass in kg of an object that weighs 25 Newton. 5) The density of a fluid is given by the empirical equation: p = 70.5 exp(8.27 x 10-7P) where p is density (Ib/ft) and Pis pressure (lb,/in.?). (a) What are the units of 70.5 and 8.27 x 10-7? (b) Calculate the density in g/cm for a pressure of 9.00 x 10 N/m?. 6) The vapor pressures of 1-chlorotetradecane at several temperatures are tabulated here. T(C) 98.5 131.8 148.2 166.2 199.8 215.5 p* (mm Hg) 1 5 10 20 100 60 Use two different method to estimate the value of P' at T = 190 °C (7) The specific gravity of gasoline is approximately 0.70. a- Determine the mass (kg) of 50.0 liters of gasoline. b- The mass flow rate of gasoline exiting a refinery tank is 1150 kg/min. Estimate the volumetric flowrate in liters/s.
= 3570 T AC =144 Example: 1.5 ft It is desired to determine the drag force at a given speed on a prototype sailboat hull. A model is placed in a test channel and three cables are used to align its bow on the channel centerline. For a given speed, the tension is 40 lb in cable AB and 60 lb in cable AE. Flow 4 ft Determine the drag force exerted on the hull and the tension in cable AC. Choc ug the h- as the free hod- DApress the
A 1:4 scale torpedo model has been built. The prototype is expected to move at a speed of 6m/s in water at 15°C. What should be the velocity in the model if, a) the test is done in a stream channel at 15°C; and b) the test is done in a wind tunnel at 27°C and a pressure of 20 atm?
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN