80 MPa, Gy35 MPa,At a point in a machine component that is subjected to plane stress, the normal and shear stresses are ox =and Txy = 42 MPa, acting in the directions shown in the figure.기OxAt this point, determine the strain components Ex, y, z, and Yxy. Assume that E = 71 GPa and v= 0.33 for the machine component.Ex =μεμεμεμradaut||EzYxy||||Txy=

Answered: Image /qna-images/answer/ae9b5b3a-adcd-459f-8f5a-5f1c9af9ae89.jpg

At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = and Txy = 42 MPa, acting in the directions shown in the figure. 80 MPa, oy 35 MPa, At this point, determine the strain components Ex, Ey, E, and Yxy. Assume that E= 71 GPa and v=0.33 for the machine component. με με με μrad "I N° II Yxy =

At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = and Txy = 42 MPa, acting in the directions shown in the figure. 80 MPa, oy 35 MPa, At this point, determine the strain components Ex, Ey, E, and Yxy. Assume that E= 71 GPa and v=0.33 for the machine component. με με με μrad "I N° II Yxy =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1250 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3780 μrad. Assume a = 2.1 mm. Calculate the magnitude of dimension b in the figure. h a Answer: b = i A W B mm X
1.5-6 The data shown in the table were obtained from a tensile test of a metal specimen with a diameter of 0.500 inch and a gage length (the length over which the elongation is measured) of 2.00 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Use the slope of the best-fit line to estimate the modulus of elasticity. Load (kips) PI223 SIN 0 2.5 3.5 10 11.5 12 Elongation (in.) 0 0.0010 0.0014 0.0020 0.0024 0.0036 0.0044 0.0050 0.0060 0.0070 0.0080 0.0120 0.0180
Answer the problem and show your solution and box the final answers. I will immediately give a rating and like for the answer.
10.Stress transformation. From the figure below, find the orientation of the maximum principal stresses, the magnitudes of the maximum principal stresses and the maximum shear stress. All formulae given at the end of the exam. 2/22 27200005 27200032 10 MPa 40 MPa 50 MPa
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 60 MPa, σy=σy= 80 MPa, and τxy=τx⁢y= 42 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 72 GPa and v = 0.29 for the machine component.
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1200 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3650 µrad. Assume a = 1.8 mm. Calculate the magnitude of dimension b in the figure. D Answer: b= i W B a mm X
The state of stress at a certain point in a stressed body is as shown in the figure. Normal stress in x-direction is 80 MPa (Tensile) and in y-direction is 40 MPa (Compressive). The radius of the Mohr's circle for this state of stress will be O, = 40 MPa O, = 80 MPa + Ox = 80 MPa Oy = 40 MPa (а) 60 MPа (b) 40 MPa (c) 20 MPa (d) 10 MPa
ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A CLEAN PAPER CLEARLY. I WILL GIVE THE FEEDBACK RATING AS POSSIBLE, YOU CAN ANSWER IT. THANK YOU
Give me right solution with clear calculations.
Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure.[a = 200 mm, b = 202.1 mm, c = 198.9 mm] For the deformed plate, determine the normal strain of diagonal PR? In micro £ For the deformed plate, determine the shear strain xy at corner P?in micro rad
For P = 100 MPa, determine the range of values of τxy for which the maximum tensile stress is equal to or less than 60 MPa. (Round the final answer to one decimal place.)
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1300 mm, and the height of the plate is h = 1700 mm. The shear strain at A is known to be +4172 μrad. Assume a = 2.9 mm. Calculate the magnitude of dimension b in the figure.