aL₁C3 of 6>Determine the orientation of the planesmaximum and minimum normal stress, ₂1 and ₂2.respectively. Use the value for 8,2 that is negative. Then use this value to determine the value of 8,1.Express your answers to four significant figures separated by a comma.► View Available Hint(s)VAΣo↓ vec?8p1, 8p2=SubmitPart B - In-plane principal stressesDetermine the in-plane principal stresses for the element (as oriented in Part A), and calculate 01and 2 such that they correspond with 81 and 8,2.Express your answers to four significant figures separated by a comma.► View Available Hint(s)IVE ΑΣΦvec?5O

Radius of the circleR=(σx-σy2)2+τxy2R=(116+282)2+642R=77.25 MPA

1: he in-plane principal stresses and ar stress along with their orientations and mal stress for an element in a given respectively. Use the value for 8,2 that is negative. Then Express your answers to four significant figures sepa ► View Available Hint(s)

1: he in-plane principal stresses and ar stress along with their orientations and mal stress for an element in a given respectively. Use the value for 8,2 that is negative. Then Express your answers to four significant figures sepa ► View Available Hint(s)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
Hiw the cross- Sectional dimensiuns of a beam are shown below. If the makimum allowabhe benehing stresS 600 Mpa. Determine the mx imum beneliny ma gnitude (M) thut Can be suppurtel by the beam. Supporn the syn is ef bending is positive. 75mm 1% mm Hw:: A beam had subjected to a postive bending moment of 5 KN. m. The Cross-Sedional dimensions are shown below. Draw the bending stress distribution on the Cross- Sedion. loo mm 15 mm 15a wm 13 mm
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
4- The stress tensor at a point under the working load condition is given. The yield stress of the material in uniaxial tension test is Fy (MPa). Based on the von Mises criterion, calculate the factor of safety of the stress state against failure if all stresses are increased proportionally to reach the yield surface. Fy (MPa) 25 50 0 σ= 50 100 0 MPa 0 0 280 -50
The stresses on an element are o, = -270 psi and o, = -540 psi. y Oy Find the maximum shear stresses (in psi) on the element. (Assume t. = 0. Use the sign convention for shear stresses.) ху (Tmax)x1 = psi (Tmaxlyı = psi (Tmaxl21 = psi
A Plane stress state is given on a material element as shown below. Os1-a+b+h T1=27 (MPa), on=b+c+d+h (MPa), ti2=c+g+h+d (MPa), O"=2(T1), E= 1000(T1) Mpa, v=(T1)/100 a) Calculate stresses (normal and shear) on AB surface. b) Find principal stress values and their directions (w/ respect to normal n of the AB surface). ) Find maximum in-plane shear stress and its direction (w/ respect to normal n of the AB surface). d) Find the volumetric and distortion strain energy densities at this point. 011=17 022=20 112= 14
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
Determine the strain energy of the tapered rod AB, where Amin is the cross-sectional area at end B. Given: Po = 4P. (Round the final answer to two decimal places.) A 2c B The strain energy of the tapered road AB is 0.25 x p²L E Amin
Question #4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. O 2. T a 0.5m 0.5m 30 kN 2 m 100mm 50mm I 10mm 10mm 180mm Section a-a 10mm