An electrical power system with a source of 240230° Vrms, 50 Hz with the loads of lighting, cooking and entertainment. If specification of the loads is 300 W with 400 VA lagging, 200 W with 0.88 power factor leading and 150 VAR with 0.77 power lagging respectively, solve this completed power system by calculating the following parameters: c) sketch a phasor diagram to show all load currents and source voltage relationship d) capacitance, C across the load if the new load power factor is 0.95 lagging

An electrical power system with a source of 240230° Vrms, 50 Hz with the loads of lighting, cooking and entertainment. If specification of the loads is 300 W with 400 VA lagging, 200 W with 0.88 power factor leading and 150 VAR with 0.77 power lagging respectively, solve this completed power system by calculating the following parameters: c) sketch a phasor diagram to show all load currents and source voltage relationship d) capacitance, C across the load if the new load power factor is 0.95 lagging

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
(b) An inductive load consisting of resistor, R and inductor, L in series feeding from a 240430° Vrms, 50 Hz supply consumes 6 kW at lagging power factor of 0.88. (i) Determine the current through the load. (ii) Find R and L. (iii) Draw the phasor diagram of supply voltage and current.
Two impedances Z₁ and Z2 are connected in series to a voltage source with voltage Vs volts. Let V₁ be the voltage across Z₁ and V₂ be the voltage across Z2. Then, the total voltage Vs is divided between V₁ and V2 in proportion to impedance values Z₁ and Z2. O a. True O b. False
AC Circuits Current, Voltage, Power, Power Factor and Phasor Diagrams. Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage source. (ii) Find the total current IT supplied by the source. (iii) Sketch phasor diagram of Vs and IT and State whether IT leads or lags Vs (iv) Determine the power factor angle for the circuit. 9. L R1 1002 0.213H IT Vs R3 1502 C 12020°V 22µF 60HZ R2 50Ω Figure 3 Answers |(1) Zr = (ii) IT= (iii)
If, in one (360 degrees), all of the instantaneous power falls under positive loops (no negativeloops), the load must be:a. A resistorb. An inductor or capacitorExplain:
Driving-point admittance The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is of O 6000 VA O 8000 VA O2000 VA 4000 VA Jump to ncements MacBook Air DD DII F10 F9 F8 000 F7 F6
(a) A very important parameter in AC power circuits is power factor. Justify this phrase. Then, explain the difference between leading and lagging power factor. Describe the phase relationship between voltage and current for these two conditions to support your answer.
For a capacitive load: a) Investigate the complex power in terms of real power, reactive power, and power factor. b) Draw the phasor diagram c) Investigate the possibility of correcting the load power factor in details. Show diagrams, circuits, equations, etc.
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
An impedance load consisting of 12 ohms resistance and 16 ohms inductance reactance is connected across a 60 Hz, 100 V source. Find the capacitance of the condenser which may be paralleled with this load to bring the power factor to 0.80 lagging.
A 3 phase 200 MVA capacitor bank is to be switched off (disconnected) the grid that operates at 13.8kV (3-phase) at 60 Hz. The capacitor is connected in a WYE configuration, therefore the voltage across each phase is VLN=7.97KV. A restrike occurs at the zero crossing of the current. Determine the magnitude of voltage across the capacitor after the restrike. b. 0.05 mSec after the first restrike the arc extinguishes, which leaves a 1st charge trapped. Another restrike occurs again 3/8 of a cycle after the first restrike and is quickly extinguished. Identify the magnitude of voltage trapped across the capacitor after the а. second restrike.
Which of the following descriptions IS NOT correct for loads in power systems? A. The purely resistive load absorbs the real power from the power grid B. The purely inductive load absorbs the positive reactive power from the power grid C. The purely capacitive load absorbs the positive reactive power from the power grid. D. The average value of the instantaneous power through loads is equal to its real power. In an ac circuit, power factor correction or improvement is achieved by A. Connecting a resistor in parallel with the inductive load B. Connecting an inductor in parallel with the inductive load C. Connecting a capacitor in parallel with the inductive load A balanced delta-load can be converted to an cquivalent balanced wye- load by dividing the delta-load impedance by A. square root of 3 В.3 C. 1/3