An exterior T-beam has a clear simply supported length of 6.75m. It has a clear distance to the next webof 3.5m. The base of the web to the beam is 350mm and has an effective depth of 500mm. Use 4-28mm diameter reinforcements with a slab thickness of 120 mm. f'c = 21 Mpa ; fy = 415 Mpa. a. effective width of the flange b. depth of compression block of the beam c. total area of the compression block d. ultimate moment capacity of the beam

An exterior T-beam has a clear simply supported length of 6.75m. It has a clear distance to the next webof 3.5m. The base of the web to the beam is 350mm and has an effective depth of 500mm. Use 4-28mm diameter reinforcements with a slab thickness of 120 mm. f'c = 21 Mpa ; fy = 415 Mpa. a. effective width of the flange b. depth of compression block of the beam c. total area of the compression block d. ultimate moment capacity of the beam

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

3 A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-∅20 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = ? Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ?? Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = ?
a) The short steel post as shown in Figure 4 is a 152 x 152 UC37 with three compressive loads applied to the top. There is a central load of 200KN and eccentric loads of 'W kN and 100kN. The maximum allowable stress on the face AB is 185 N/mm?. (Area=D47.1cm2,Zxx=273cm) What is the value of the load 'W in kN? WkN A. 152 x 152 UC37 100mm -200KN 50mm 100KN Not to scale Figure 4
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
a. Compute the vertical deflection at midspan due to flexural deformations only. b. Compute the vertical deflection at midspan due to shear deformations only. Compute the total vertical deflection at midspan. C. w E, G, I, Av L 12 A
An existing T-beam section was investigated and found out the following elements: Top bar reinforcement: 1500 mm2 Bot bar reinforcement: 2500 mm2 thickness of slab = 100mm effective depth from the surface of the slab = 450mm effective width of flange = 1000mm Top bar concrete cover at center of the bar = 50mm fy = 414Mpa f'c = 28Mpa use f’y = fy Determine the depth of compression block in mm, in 3 decimal places.
Determine the flexural capacity of the given section of beam below. b=350 d=615 d'=100 fc'=34 fy=415 As-5-36mm As'=2-25mm A.USE NSCP 2001, Mu = kN-m B.USE NSCP 2015, Mu = kN-m
A W 305 x 87, 7.5m llong, is pinned at both ends and braced in the weak direction at the third points. Determine the available compressive strength. Properties: A = 10,965 mm² lx = 331.2x106 mm4 ly = 55.78x106 mm4 •• Please Show Solutions Steel Design: Civil Engineering Answersi Pn=Fer Ag= 274.61 (10965) 1000 Pn=3011.05 KN
. Determinę the maximum allowable load P that can be safely supported by the frame if t = 32 mm and b = 90 mm. The wood has a normal failure stress of 42 MPa ksi, and a shear failure stress of 8 MPa. Use a factor of safety against failure of 2. а. 74 KN с. 64 KN b. 44 KN d. 54 KN 75 mm K45 45 C B, 75/mm
Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and determine the design flexural strength (Moment) for it, use: • f = 20 MPa. • fy = 420 MPa. Effective depth d = 610 mm. • Reinforcement is 6Ø25mm (ABar = 490 mm?). 500 mm 125 mm 700 mm 6Ø25mm 250 mm
A simply supported rectangular beam has a width of 300mm and an effective depth to the centroid of tension reinforcement of 330mm. The tension reinforcement has an area of 2463mm2 and the area of compression reinforcement placed 70mm from the compression face of the beam is 1231.5mm2, fy = 415MPa, fc’ = 30MPa. Balanced steel ratio is 0.031. The design strength using 0.90 as the reduction factor is _____kN.m
AT:Design the steel reinforcement for flexural for the beam shown in the kN fig.below The dead load on the beam is 100 (not include self weight) & the live load is 200KN. useØ25mm& Use effective cover in top& bottom=60mm, use fc' = 27.6 Mpa, fy= 414Mpa. Ptive=200KN kN D.L= 100 d= 550mm 275mm 3m Зт
A simply supported rectangular beam of length L has a width of b and an effective depth of d. Compression steel bars are placed at a distance d' from the extreme concrete compressive fiber. The beam supports service dead loads of wD and wl, respectively. Use fc'= 28 MPa and fy = 420 MPa. For the reinforcements, use 4 20 mm tension steel bars and 4 10 mm compression steel bars. b= 390 mm d= 615 mm d'= 165 mm L= 5.85 m Wd= 27.79 kN/m WI= 32. 25 KN/m Questions 1. Calculate the height of the neutral axis measured from the extreme compression fiber. 2. Calculate the strength reduction factor for the given beam. B. Calculate the design moment for the given beam.