10 mm| | | |10 mm50 mmارت -50 mm10 mm20 kNB150 mm910 mm10 kND-------150 mmTwo vertical forces are applied to a am of the cross section sh vn.Determine the maximum tensile and compressive stresses in portion BC of thebeam.Show your complete solution and box your answer.

Answered: Image /qna-images/answer/40619c3f-1db5-4cd7-8e7f-93b7b25beb53.jpg

10 mm 10 mm | | | |- | 50 mm 50 mm 10 mm الے 20 kN B 150 mm 910 mm 10 kN C 150 mm D Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.

10 mm 10 mm | | | |- | 50 mm 50 mm 10 mm الے 20 kN B 150 mm 910 mm 10 kN C 150 mm D Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plate with width of 300mm and thickness of 20mm is to be connected between two plates 12mm thick with same width by 4-25mm diameter rivets a shown. The rivet holes have a diameter 2mm larger than the rivet diameter. The plate is A36 steel with yield strength Fy=248 Mpa and Fu-400MPa. The rivets have nominal shear stress capacity of 165MPa. O 803 O 1490 • Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates (consider yielding and rupture of plates ONLY) in KN O 1180 O 1340 ο ο ο ο ο P3 O 1968 O 590 O 670 O 893 O 707 OO 150 O 1180 P1 P2
2m 2m 12₂ 2m y 2N/m ✓ 2N/m 2m $ بلا
A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
In the assembly of the bronze tube and steel bolt, the pitch of the threads is p = 1/32 in.; the cross-sectional area of the bronze tube is 1.5 in? and of steel bolt is 4 in?. the nut is turned until there is a compressive stress of 4,000 psi in the bronze tube. Find the stresses (psi) if the nut is given one additional turn. How many turns of the nut will reduce these stresses to zero? Use Epr = 12 x 106 psi and E = 29 x 10° psi. L= 40 in.
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. Please show your complete handwritten solution. Thank you
T'he pin is made of a material having a failure shear stress of Tail = 100 MPa. Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of F.S. = 2.5 against shear failure. %3D 80 kN
The two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in each bolt; and (b) shearing stress at the mid- height of the upper steel plate. 150 mm 12 mm 250 mm 12 mm Solution:-
A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters by 25 millimeters diameter rivets. The rivets holes have a diameter 2 millimeters larger than the rivetdiameter. The plate is A36 with yield strength F, = 248MP.. Allowable tensile stress on net area is 0.6Fy and allowable bearing stress of 1.3Fy. The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150MPA. 1. Detemine the maximum load that can be applied to the connection with consideration to the yielding failure in the plates. 2. Detemine the maximum load that can be applied to the connection with consideration to the fracture failure in the plates. 3. Detemine the maximum load that can be applied to the connection without exceeding the allowable shearing stress in the rivets. 4. Detemine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between…
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.