An electric system is rated 20 kVA, 240 V at a 0.558 lagging power factor: a) Determine the impedance of the system in rectangular form. b) Find the total resistance and the total reactance (inductive or capacitive) within the electric system. Assume that all elements are in series. c) Find the average power delivered to the system.

An electric system is rated 20 kVA, 240 V at a 0.558 lagging power factor: a) Determine the impedance of the system in rectangular form. b) Find the total resistance and the total reactance (inductive or capacitive) within the electric system. Assume that all elements are in series. c) Find the average power delivered to the system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158 volts, 50 Hz supplies the combination. Determine the following: a. Circulating current b. Voltage across the resistor c. Voltage across the capacitor d. Real power supplied by the source e. Reactive power supplied by the source f. Apparent power of the circuit g. Power factor of the entire circuit
If, in one (3600), all of the instantaneous power falls under positive loops (no negative loops), the load must be:a. A resistorb. An inductor or capacitorExplain:
Which of the following descriptions IS NOT correct for loads in power systems? A. The purely resistive load absorbs the real power from the power grid B. The purely inductive load absorbs the positive reactive power from the power grid C. The purely capacitive load absorbs the positive reactive power from the power grid. D. The average value of the instantaneous power through loads is equal to its real power. In an ac circuit, power factor correction or improvement is achieved by A. Connecting a resistor in parallel with the inductive load B. Connecting an inductor in parallel with the inductive load C. Connecting a capacitor in parallel with the inductive load A balanced delta-load can be converted to an cquivalent balanced wye- load by dividing the delta-load impedance by A. square root of 3 В.3 C. 1/3
A synchronous generator may be represented by a voltage source of magnitude 1.7 p.u. in series with an impedance of 2 p.u. It is connected to a zero-impedance voltage source of 1 p.u. The ratio of X/R of the impedance is 10. Calculate the power generated and the power delivered to the voltage source if the angle between the voltage sources is 30°.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage.b) write the expression of the instantaneous current.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage. b) write the expression of the instantaneous current.
50. A series resistance-capacitance (R-C) circuit is connected to 230-volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: a. Ohmic value of the resistor b. Capacitive reactance E. capacitance in microfarad
An alternating voltage of 110 volts is applied to a circuit with resistance of 8.66 Ohms, inductance of 0.106 Henries, and capacitance of 75.8 microFarads. The frequency of the voltage is 50 Hz. Determine: a. The current in the circuit and its phase angle relative to the applied voltage. b. The voltage drop across each component of the circuit. c. The active and reactive power inputs to the circuit. d. Draw (Not hand-sketch) the equivalent power triangle. e. Is the RLC load of the circuit inductive or capacitive? Why?
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
Assume that the voltage applied to a load is V = 208- 30° V and the current flowing through the load is I = 5415° A a. Calculate the complex power S consumed by this load. b. Is this load inductive or capacitive? c. Calculate the power factor of this load. d. Calculate the reactive power consumed or supplied by this load. Does the load consume reactive power from the source or supply it to the source?