An auditorium is designed to seat 4500 people. The ventilation rate is 1.62×107 ft³/hr of outside air. The outside temperature is 0°F dry bulb, and outside pressure is 14.6 psia. Air leaves the auditotium at 70°F dry bulb. There is no recirculation. The furnace has a capacity of 1,250,000 Btu/hr. The temperature at which the air should enter the auditorium is most nearly?

An auditorium is designed to seat 4500 people. The ventilation rate is 1.62×107 ft³/hr of outside air. The outside temperature is 0°F dry bulb, and outside pressure is 14.6 psia. Air leaves the auditotium at 70°F dry bulb. There is no recirculation. The furnace has a capacity of 1,250,000 Btu/hr. The temperature at which the air should enter the auditorium is most nearly?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 15RQ: Why is information regarding the specific volume of gases important to the designer of...

See similar textbooks

Similar questions

You are working in the compressor design department of a large compressor manufacturer. As the new junior engineer you have been assigned to a large project and you are responsible to do preliminary thermos-fluids design of a centrifugal air compressor that can supply (266)kg/min of air at a final delivery total pressure of 312kPa. The project manager has advised you to assume the ambient air conditions as 101.55 kPa and 26 degrees Celsius. Further you have been given boundary conditions to help you with compressor design. You must assume that the compressor runs at 19925rpm with isentropic efficiency of 90%. Also assume the is no pre-whirl at the inlet and the inlet hub diameter is 13.4cm and the air enters the impeller eye with a velocity of 158 m/s. Assume the ration of Vw2/U2 (whirl speed to tip speed is (0.804) 1. stagnation temperature in degrees clelcius and the total pressure at the inlet kPa of the compressor 2. stagnation temperature in degrees celcius at the end of…
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
(b) Bathroom sinks and some other fixtures include an overflow opening in the basin. This opening is located on the wall and near the top of the basin. The overflow opening serves two important functions: If the water tap is left on while the drain stopper is closed, the opening will channel water down into the drain opening rather than letting is spill out of the sink onto the floor. The overflow allows the sink to drain faster by introducing air into the system. A sink with a dimension given in Figure Q2(b), has water flows into it at a rate of 8 L/min. If the drain stopper is closed and water level in the sink remains constant, determine the average velocity of water flows through the 3.0 cm diameter overflow hole. Front 3 cm diameter overflow holes Q-8 L/min 15 3/4| 40 cm 15 cm Side (a) Figure Q2: (a) Picture of the sink; (b) Sink dimension (Ь)
Steam leaves an industrial boiler at 645.3kPa and 151.2°C. A portion of the steam is fed through a throttling calorimeter and released to the atmosphere when the calorimeter pressure exceeds 104.3kPa. If the calorimeter's steam temperature is 113.8°C, a. What is the amount of moisture that is escaping from the boiler container? Show unit analysis & conversion. b. Calculate the mass of the saturated vapor if the mass of the saturated liquid is 15kg. Show unit analysis & conversion. @645.3kPa and 151.2°C: hf = 624.56kJ/kg hfg =2123.3kJ/kg @104.3kPa and 113.8°C: h2=2506.7kJ/kg
17) What is the approximate Peritectic Temperature for the system?
O a. None of these O b. Absolute pressures and heat capacity ratio O C. Absolute pressures and temperatures O d. Gauge pressures and temperatures In perfect gas law experiment, the pressure pump coupling is used to connect the vacuum vessel to the pump discharge connector. Select one: O a. False O b. True Which part in the mechanical heat pump is used to reduce the refrigerant pnessule? Select one:
Refer to the Fe-C Diagram below to answer the following questions T(° C) 1600 1400 (Fe-C System) y +L IFe,C 1200 1148°C (austenite) www 1000 v + Fe,C 800 727°C a 600 a +Fe,C 400 5 C, wt% C 4 6. 6.7 (Fe) Fe,C(cementite)
10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler pressure of 2 bar gauge and polytropic index of 1.3, what will be the flowrate at the exit of the intercooler ?Please choose correct option.a.4.295 m3/minb.312 litre/sec.c.3333 litre/mind.1172 litre/min.e.981 m3/min
Determine the output pressure of a compressor operating with the following data: a. Actual power required to drive the compressor is 20 kW. b. Overall efficiency of the compressor is 75%. c. Compressor delivers four standard m3/min. d. Compressor inlet pressure is 100 kPa abs.
A chiller tank with a water volume capacity of 20 M3. There are 2 chiller units with a capacity of 20 PK each to cool the water in the chiller tub. 1 unit of cold chiller water transfer pump is used to the production area with a capacity of 5 M3/hour. The chiller water temperature sent to production is 15 oC and the pressure is 4 bar. The distance of the 2 inch stainless pipe from the chiller pump to the double jacket mixing tank production is 100 meters. The diameter of the inlet and outlet pipes for the double jacket mixing tank is 1 inch. The chiller water storage capacity in a conventional double jacket mixing tank is 400 liters. (mixing tank capacity is 1500 kg). Questions: 1. How much time is needed to cool the water in the mixing tank from the initial temperature of 90 oC to 40 oC? 2. How much energy (BTU) is needed to cool the water temperature from 90 oC to 40 oC? 3. How much energy is lost along the 100 meters of chiller water transfer pipe? 4. If the number of 1500 Kg…
A manufacturing company is intending to use its water cooled condenser for its proposed cold storage room. The name plate of the condenser gives the following specifications: refrigerant ammonia condenser water inlet 30 OC condenser water outlet 40 ỌC condensing temperature 35 OC refrigerant flow 3.84 kg/min circulating water flow 120 kg/min If the company decided to purchase a new compressor and evaporator, find the tonnage of the system and the temperature in the evaporator, (b) what is the COP? (c) find the theoretical hp required.
1. The mean effective pressure of an engine running at 300 rpm is 500 kPa. What is the indicatedpower if the engine has bore of 250 mm x 450 mm. Select the correct answer below: A. 110.5 kW B. 150 kW C. 200 kW D. 182. 2 kW 2. In a certain process, entering is 1500 KJ/kg and 150 m/s. If the energy leaving is 12000 Kj/kg/ Determine the velocity at exit. Select the correct answer below: A.) 145 m/s B. 1020 m/s C. 789 m/s D. 978 m/s