An aluminum wire having a cross-sectional area equal to 4.60 x 106 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s

An aluminum wire having a cross-sectional area equal to 4.60 x 106 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter1: Fundamentals Of C++ Programming

Section: Chapter Questions

Problem 2PP: (Conversion) An object’s polar moment of inertia, J, represents its resistance to twisting. For a...

See similar textbooks

Similar questions

The circular rod shown is made of the steel alloy AISI 4140 OQT 900. It has a diameter of 1.00 in and an initial length of 48 in. An axial tensile load of 15 000 lb. is applied during a certain operation. Compute: 1. the equivalent spring constant K, 2. the deformation X of the rod. The Young's modulus of the steel is known to be 30,000,000 psi. F=15 000 lb L= 48 in F=15 000 lb
The displacement of an oscillating spring can be described by x = A cos(wt) where x = displacement at time t, A = maximum displacement, w = angular frequency, which depends on the spring constant and the mass attached to the spring, and t = time. Find the displacement, x, with maximum displacement A of 4 cm, for times from 0 to 120 seconds with increments of 30 seconds, and angular frequencies from 0.4 to 0.6 radians/sec, with increments of 0.1 radians/sec. The displacement for all combinations of times and angular frequencies needs to be calculated. Use meshgrid. Display your results in a matrix with angular frequencies along the top row and times along the left column like so (you may put zero, 0, or NaN, in the upper left corner:
Calculate the kinetic energy in Joule, of a car of mass 1700kg travelling at 90km/h.
2. Compute the kinetic energy, in joules, of a 3 g rifle bullet travelling at 300 m/s.
The coefficient of linear expansion of an metal plate is 9 x 10-6 /oC. The internal diameter of the metal plate at 20 oC is 2.2 cm. When heated, its area change, if the final diameter is 2.8 cm, what is the final temperature?
(Conversion) An object’s polar moment of inertia, J, represents its resistance to twisting. For a cylinder, this moment of inertia is given by this formula: J=mr2/2+m( l 2 +3r 2 )/12misthecylindersmass( kg).listhecylinderslength(m).risthecylindersradius(m). Using this formula, determine the units for the cylinder’s polar moment of inertia.
The following is used to model a wave that impacts a concrete wall created by the US Navy speed boat.1. Derive the complete piecewise function of F(t) and F()The concrete wall is 2.8 m long with a cross-section area of 0.05 m2. The force at time equal zero is 200 N. It is also known that the mass is modeled as lumped at the end of 1200 kg and Young’s modulus of 3.6 GPa2. Use *Matlab to simulate and plot the total response of the system at zero initial conditions and t0 = 0.5 s
Determine the transfer function, of the rotational mechanical system shown in T(s) Figure Q2. The variables 6,(t) and 02(t) refer to angular displacement of motion, while T(t) is a torque applied to the system. Given the value of spring, damping coefficient and inertia as; J: 5 kg-m? Di: 5 N-m-s/rad J2: 10 kg-m? K : 6 N-m/rad K2 : 5 N-m/rad D::4 N-m-s/rad D3:2 N-m-s/rad T(t) e,(1) D2 K2 0000 D1 D3 Figure Q2
When a tension force of 900 N is applied to a steel wire, it is assumed that E = 210 GPa and that the diameter of the wire increases by 1.05 mm. Calculate the diameter of the wire.
Aan TUUR IEACHER The four particles shown below are connected by rigid rods of negligible mass where y,6.60 m. The origin is at the center of the rectangle. The system rotates in thexy plane about mezawth an angular speed of 5.90 rad/s. 3.00 kg 2.00 kg 200 kg L00 kg 4.00 m- (a) Calculate the moment of inertia of the system about the z axis. kg m? (b) Calculate the rotational kinetic energy of the system
2. calculates the trajectory r(t) and stores the coordinates for time steps At as a nested list trajectory that contains [[xe, ye, ze], [x1, y1, z1], [x2, y2, z2], ...]. Start from time t = 0 and use a time step At = 0.01; the last data point in the trajectory should be the time when the oscillator "hits the ground", i.e., when z(t) ≤ 0; 3. stores the time for hitting the ground (i.e., the first time t when z(t) ≤ 0) in the variable t_contact and the corresponding positions in the variables x_contact, y_contact, and z_contact. Print t_contact = 1.430 X_contact = 0.755 y contact = -0.380 z_contact = (Output floating point numbers with 3 decimals using format (), e.g., "t_contact = {:.3f}" .format(t_contact).) The partial example output above is for ze = 10. 4. calculates the average x- and y-coordinates 1 y = Yi N where the x, y, are the x(t), y(t) in the trajectory and N is the number of data points that you calculated. Store the result as a list in the variable center = [x_avg, y_avg]…
If the crystal lattice constant is the length of the edge of the cube crystal unit in sodium, whose composition is type (BCC) equaí to (4.24A°) angstroms. What is the distance between two neighboring atoms? Calculate the sodium density if its atomic weight is (23).