An acetal disk 5mm thick by 25mm diameter is used as a cover plate in a mechanical loading device. If a 20kN compressive load is applied to the flat surfaces of the disk, calculate the disk's resulting diameter while under load.

An acetal disk 5mm thick by 25mm diameter is used as a cover plate in a mechanical loading device. If a 20kN compressive load is applied to the flat surfaces of the disk, calculate the disk's resulting diameter while under load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1) A cylindrical titanium bar, an initial length of 10 inches and a diameter of 0.167 ft, is subjected to loading. After loading, the initial length of the 10-inch bar is reduced to 9.998 inches. Since the young's modulus of the titanium bar is 16.5*106 psi, find the load (kip) acting on the bar. Indicate whether the loading is tension or compression.
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
#3 solution?
An aluminium wire (E=10,600 ksi) having a diameter d=1/8 inch. and length L=14 ft is subjected to a tensile load P. If the maximum permissible elongation of the wire is 1/6 inch and the allowable stress in tension is 10 ksi, what is the allowable load Pmax? Answer in Ibs
A prismatic aluminum bar has cross-sectional dimensions 40 x 60 mm and a length of 350 mm. The modulus of elasticity is 70 GPa and Poisson's ratio is u=0.35. When an axial load of 100 kN is applied, the proportional change in the bar's volume is
I need typing answer urgent
1. The following data were obtained during a tension test of an aluminum alloy. The initial diameter of the test specimen was 0.505 in. and the gage length was 2.0 in. Load (lb) 0 2 310 4 640 6 950 9 290 11 600 12 600 Elongation (in.) 0.00220 0.00440 0.00660 0.00880 0.0110 0.0150 Load (lb) 14 000 14 400 14 500 14 600 14 800 14 600 13 600 Elongation (in.) 0.020 0.025 0.060 0.080 0.100 0.120 Fracture Plot the stress-strain diagram and determine the following mechanical properties: (a) proportional limit; (b) modulus of elasticity; (c) yield point; (d) yield strength at 0.2% offset; (e) ultimate strength; and (f) rupture strength.
Plz complete solution.
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
Internal diameter of a steel shaft is 70% of external dia and the shaft has to transmit 3500 kW at 200 rpm. If the maximum shear stress is 50 MPa, the diameter of the shaft is__mm. (Report your answer in mm)
4.20 A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the magnitude of the load required to produce a 10 in. change in diameter if the deformation is entirely elastic. Assume a Young's modulus of 11 X 106 psi and a Poisson's ratio of 0.33.
A closed right circular cylinder has radius 2 units and height 17 units A load of an unknown weight is put on top of the cylinder, causing the cylinder to shorten by 1.1 units. Find the new volume of cylinder due to this deformation in the height of the cylinder.