3. A rectangular steel block is subjected to triaxial loading as shown. If v = 0.3 and E = 200 Gpa, Determine a single distributed loading in the y direction that produced the same x deformation as the original loading. 267 kN

Q: Determine the coordinates of the 60 mm Centroid of the shaded area shown 30 mm in item 3. 30 mm X 45…

A:

Q: What is Non-Dot Standard Specification?

A: Specification of Non-Dot Standard:

Q: 600 80 500 MPa 600- 10 psi 80 60 400 400 60 300 40 40 200 200 20 20 100 todos 0.005 0.05 0.10 0.15…

A: Given stress- strain diagram

Q: 2000 MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0.000 0.020 0.040 0.060 0.080 Strain Stress…

A: Considering the given stress- strain graph the solutions are provided in the following steps-

Q: Draw and label the standard symbols used in a horizontal stadia sight. Define each symbol used.

A:

Q: hat are 3D input devices, and how are they utilized in fields like computer-aided design (CAD) and…

A: In fields such as computer-aided design and virtual reality, 3D input devices are revolutionizing…

Q: lgorithm for drawing this in CAD.

A: please follow steps.

Q: I would appreciate it if you could explain what you mean when you say "GIS."

A:

Q: he top, front and side views of Figure 2 with scale 1:1. The dime to the drawings.

A: Here they have given an object to draw top view, front view, and side view projections. Top view…

Q: Discuss how is CAD/CAM integration helpful for a designer and a manufacturer.

A: CAD  full-form is for computer-aided design and CAM full-form is computer-aided manufacturing.…

Q: What is Universal Transverse Mercator (UTM)?

A: A Universal Transverse Mercator is method to represent the three dimensional earth into two…

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: Differentiate between BIM and 3DModeling?

A:

Q: Explain how the symbol modes of Live and Rectangle mode, Arc and Circle mode, Dimension and…

A: Introduction:- Geographic Information systems in the area of surveying involve the development of a…

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: 13.1500 13.1500 4 0000 - -2.0000 4.0000 -3.3500 0.0000 2.0000- 3.8000 -3.3500 2.0000 2.0000 2.0000…

A: We need to find out One Way Slab and Two way slab If Ly/Lx is equal to or more than 2 then One way…

Q: Enumerate and explain briefly each of the steps and processes involved in iterative design…

A: Introduction- The Iterative designing concentrates on cyclical or gradual progress. If you want to…

Q: Enlarges or reduces selected objects, keeping the proportions of the object. explode command…

A: Answer - Scale command Explanation- Enlarges or reduces selected objects, keeping the proportions…

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: The distance between two lines is determined in the multiline command by one of :the following…

A:

Q: top view drawing

A: In top view we see the object from top. Here dotted line represents a cut inside the object.

Q: REQUIRED: ISOMETRIC DRAWING VEN FIGURE SHOWN TOP VIEW syooing 0.5cm FRONT VIEW RIGHT SIDE VIEW 45

A:

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: front view

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: Describe what is Translational slides.

A: Translational slides:

Q: If you are using the standard dimension style (not annotative) and want the text on paper space to…

A:

Q: Draw the top, front, and right side view of the given isometric drawing

A:

Q: Find the correct front view for the drawing given below.

A: i drawn a rough sketch of ront view   see it in below step

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View,…

A: Hand made drawing are attached herewith of different views. Which will give you idea about different…

Q: draw the front view, side view, and top view

A: Isometric view is given. We need to draw front view, side view and top view

Q: Where is the APPLICATION MENU icon located in AutoCAD, and what is it? Where is the STATUS BAR…

A: 1. In AutoCAD, application menu icon is located at the top left corner.     It is the icon used to…

Q: In detailed assembly drawing, part's information contains. Select one: O a. orthographic views O b.…

A: Option a( orthographic views) is correct

Q: Shapes Shown Below, Using Scale (1:1) 13 38 $25

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: Please send Complete answer for getting upvote  Detailed answer  what is Decorator Design Pattern…

A: decorator design patter is actually a structural design pattern. actually it is a programming that…

Q: GIVE 3 PLUMBING COMPONENTS

A: To find out the three main component of plumbing and define all of them.

Q: Please encode the solution

A: given: diameter of bolt=3/4 inch, thickness of plate=5/8 inch required: to encode the solution…

Q: Please give typed answer

A: Given data:- Draw a horizontal line S60W with a length of 200m, Calculate the value of TL.

Estimating construction costs

The determination of the cost of various items that would be required to carry out a construction project successfully is termed the estimation of construction costs. For preparing an estimate, the quantities of the materials are calculated from the construction drawings or blueprint design using formulas, and using these quantities, the construction cost estimating is done. The estimation process can be manual or it can be computed using construction estimating softwares such as RSmeans, STACK, and ProEst.