All two-force members of the loaded structure are of the same length. Member BCD is a rigid beam. Determine the forces in membersBG and CG. The forces are positive if in tension, negative if in compression.AAnswers:BG=CG =iiBGLLLE

Answered: Image /qna-images/answer/dc5e16bf-2b3b-4baf-b163-ba698c0dd1f6.jpg

All two-force members of the loaded structure are of the same length. Member BCD is a rigid BG and CG. The forces are positive if in tension, negative if in compression. A Answers: BG= IM CG= i B G L D L L E

All two-force members of the loaded structure are of the same length. Member BCD is a rigid BG and CG. The forces are positive if in tension, negative if in compression. A Answers: BG= IM CG= i B G L D L L E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In a residential area of 20,000 inhabitants, the specific water demand is estimated at 50 l/c/d…

A: Population = 20,000Demand = 50 l/c/dmaximum flow = 24 l/s

Q: A wave train is propagating normally toward the coastline. The bottom has straight and parallel…

A: The characteristics of a wave is shown below,Here, L = Horizontal distance between two crests or…

Q: How does IoT impact the energy management and sustainability of buildings? Provide examples.

A: Energy management in the building plays an important role to attain energy efficiency and cost…

Q: What is the one benefit of an eccentrically braced frame (EBF) b) Would you expect to have more or…

A: Braced frames are used to resist lateral loads such as wind or earthquake forces. To reduce lateral…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: In order to check the beam adequacy for web crippling let us first find the Nominal web crippling…

Q: Use Simpson's 1/3 rule to estimate the integral of the following data set. Make sure to show all of…

A: the data is given as followsulate estimated

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

A: Modular ratio has to be determined.Lever arm has to be determined.Then the stress in concrete and…

Q: Q1-5/ If concentration of total dissolved salts in Shatt Al- Arab water C 6000 (p.p.m) and the Shatt…

A: Concentration of total dissolved salts, C = 6000 ppm Water flow rate, Q = 200 m3/sTo find the weight…

Q: BM 1 STA BM 1 BM 1 El.- 100.00 X 4.683 HI == Benchmark El.- 100.0 IP#1 BS Existing Building TP 1…

A: Given data,Benchmark 1=100'From IP#1BS=4.683' & FS=5.812'

Q: A horizontal channel with rectangular cross-section has a width of B₁ = 3 m and depth of y₁ = 1.55…

Q: Estimate the flow under the dam below given: k = 5.2x10^-4 cm/s, h1 = 32ft, h2 = 11ft. Answer in…

A: Coefficient of permeability, To find: Flow under the dam.

Q: 3m 3 m 3m 3m D B 2a+b F G P H 4. Determine the force in member EI. Give a positive value if the…

Q: A Find AA, B s' B für 3 Q Search ܣܐ 2K/₁ f Find AB, Oc Con side B-C), 8 (unside C-D). pla 4K $31…

A: To calculate support reactionsThe moment at right support = 0

Q: sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3…

A: Initial reading = 2.3 metersFinal reading =1.8 metersEach division in the level tube= 0.6 mmDistance…

Q: Figure ▼ Part A FCB = Value 4 ft Submit Request Answer 3 ft Determine the force in member CB of the…

Q: A w = 4 kN/m 10 m C B K= 40 kN/m

A: Length of beam = 10mE = 200 GPaI = 60 × 10⁶ mm⁴K of spring = 40 KN/m Udl load on cantilever of…

Q: A rigid bar AB is supported by two elastic members BC and BD (Figure P3.2). If the bar AB rotates…

A: Given data,A rigid bar AB is supported by two elastic members BC and BDbar AB rotates clockwise…

Q: he beam-column is fixed to the floor and supports the load shown. Determine the normal force, shear…

A: Normal force, which acts perpendicular to the beam's cross-section, is called the axial force, while…

Q: 22: A small village is located near a stream that is to be used as the source of water supply for…

A: Minimum flow in the stream = 550 m3/hPopulation in 2008 = 10000 in 2058 = 30000…

Q: 2 m B 2m |C -2m E D 4 m 700 N 500 N 2. The truss above is supported with a roller at A and a pin at…

A: Given:Required:Zero force memberSupport reactionForce in GF, GC and BC

Q: Determine reactions at A and B .

Q: The zone production and attraction values were estimated as follows, where the values are…

A: The trip distribution matrix is a transportation planning and traffic modeling, particularly in the…

Q: Match the six types of hydraulic losses that occur in pumps with their definition. Flow Friction…

A: Flow friction: It is the loss brought on by flow resistance brought on by the fluid's velocity and…

Q: Design a W14, 20ft long column to carry an axial load of 800k. Fy=50ksi, fix - pin condition and…

A: Length of column about X axis(Strong direction) Lx = 20 ftLength of column about Y axis(Weak…

Q: Numerical answer in 4 decimal places and positive values only: kN (Upward) RA MA Rg= M₂ . kN-m (ccw)…

Q: Use the moment-area method to determine the slopes and deflections at points B and C of the beams…

A: "Since you have posted multiple questions, I will solve first for you as per guideline"

Q: Draw a single FBD that would allow you to solve for the force in members DG, DF, and EF knowing that…

A: Determine the force in members DG, DF and EF. Let's solve using method of section.

Q: The stress on a structure is as follows. The EI of the ?-shaped part of the structural section is…

Q: For the beam and loading shown. Given: P = 170 kN. 131 FL 450 mm. -600 mm 72 mm 72 mm 72 mm a -t 192…

A: Given data,cross section is givenP=170KNlength of beam=600mmsection taken at 450mm from free…

Q: Determine the force in members FE, FB, and BC of the truss and state if the members are in tension…

A: Determine the force in members FE, FB and BC of the truss. Note:- 1kip = 1000 lb

Q: EP 6.4 Given: air flows into the gas heater at a steady rate, such that at A its absolute pressure…

A: Gievn data,Air flows into the gas heater at 203 kPasteady velocity of 15m/s through a 100mm…

Q: What is the Contractor payment? I don't understand what it means in the question's note.

A: contractor in a person which provide different types of services to the owner for example:- In…

Q: 12. A 4 m tall, 1.2 m diameter barrel filled with hardened cement mortar is dropped across a 4 m…

Q: From the given closed traversed shown LINES AB BC CD DE EA BEARING S 35° 30' W N 57°15' W N 1° 45' E…

Q: 03: For the beam shown in Figure (3), given INA = 1. 106mm, calculate the transverse shearing stress…

A: Where,B = Overall width of I section of the beamD = Overall depth of I section of the beamb =…

Q: Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line…

A: The pressure head,

Q: Select the lightest pair of C9 channels to support the loads PD = 50 k and PL = 90 k. The member is…

A: Dead load, DL=50 kLive load, LL=90 kLength of the member is 20 ft.Grade of steel is A36Diameter of…

Q: A reinforced concrete beam has the following properties bw=300mm d= 450mm f'c = 28Mpa fyt=275MPa. If…

A: bw=300mmd= 450mmf'c = 28Mpafyt= 275MPaFactored shear force at the critical section is 100 kN10mm…

Q: diversion gate backs up flow in a 5-ft wide rectangular irrigation channel (S0 = 0.001, n = 0.015).…

A: A diversion gate backs up flow in a 5-ft wide rectangular irrigation channel (S0 = 0.001, n =…

Q: dị 200 mm a

Q: Calculate the force in members AE, AB, DE and BE the loaded truss below. Indicate whether the…

Q: The midpoint of a cantilever beam 6 m long rests on the midspan of a simply supported beam 8 m long.…

Q: Determine the magnitudes of the pin reactions at A and D. Neglect

Q: Given: shown below are a round pipe: each velo profile has the velo. some statements about this flow…

A: Given:Maximum velocity in pipes A and B is sameRequired:Relation between average velocity in A and…

Q: Q.1 Determine the slopes and deflections at B and C of a cantilever beam shown in Fig., by Moment…

A: Given:Required:Slope and deflection at B and C

Q: Please

Q: Draw the complete shear and moment diagrams for the loaded beams shown. Indicate minimum/maximum…

Q: Example For the branching system shown in Fig. 11.14, calculate the discharge each pipe. Take f =…

A: Determine the discharge in each pipe.

Q: Calculate the support reactions and draw the shear and moment diagram for each beam shown below…

Q: 2- A 6-m wide concrete-lined trapezoidal channel (n = 0.013) has a sidewall slope of 1V:1.5H, a…

A: Bottom width of channel, Manning's constant, Side slope, Longitudinal slope, Discharge, To find:…

Concept explainers

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.

Question

All two-force members of the loaded structure are of the same length. Member BCD is a rigid beam. Determine the forces in members
BG and CG. The forces are positive if in tension, negative if in compression.
A
Answers:
BG=
CG =
i
i
B
G
L
L
L
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the force in members BG and CG

VIEW

Step 2: Determine the force in members BG and CG

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the force in truss DE. T = 390 N, x = 1.8 m. (Note: if the force in the truss is in tension, please enter a positive value; if it is in compression, please enter a negative value.) A F
A rigid beam loaded with negligible mass is pinned at Band is supported by two identical rods, except for thelength. SHOW FBD AND DEFORMATIONA) Determine the force in rod CB) Determine the force in rod D
From the given truss shown, FA = 150, FB = 200, and FC = 250 N. Compute the following. Specify whether the forces in each member are in tension or compression. a. find the reaction at C b. find the force in member AC c. find the force in member CD d. find the force in member AD
Solve for Members BF,BC,EF
ABCD is a rigid rod. Cross section area of AE=BF=400 mm2 Find the normal stresses of the bars ae and BF. Calculate the displacement of point D E=200Gpa
The steel bars AC and BC, each of cross-sectional area 120 mm^2, are joined at C with a pin. Determine the displacement of point C caused by the 15-kN load. Use E=200 GPa for steel. Include the ff:force on bar ABforce on bar BCwhat is the displacement of point C
three forces are exerted in the joint of a truss as shown. The system is in equilibrium. draw the force polygon for the equilibrium in the joint. determine the forces n1 and n2. are they tensile or compressive forces
Solve for Force CH (Fch). state if compression or tension
A roof truss is loaded and supported as shown in Figure 2. The joints are all pinned. Take L = 3 m and e = 35°. (a) If P = 500 N, determine the support reactions at A and D. (b) If P = 500 N, find the forces in all the members of the truss. State whether each of the members is in tension or compression. (c) Determine the maximum magnitude P of the two loads that can be applied to the truss, if the maximum allowable tensile force in the members of the truss is 2 kN and the maximum allowable compressive force is 1.2 kN. BY 7. Figure 2
Two members AB and AC are made of material with E= 91 Gpa and each member has cross sectional area of A= 290 mm2. The members are used to support bar BC. If P=2079 N, L1= 202 mm , L2= 313 mm and L3= 480 mm . Answer the following questions. The tension in member AB The tension in member CD The elongation in member AB The elongation in member CD Vertical displacement of point E
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel.
The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. If P1 = P2 = 4 kN, the force in member (CB) is equal to. %3D A 30° 30° OC E D 3 m 3 m P1 P2 Select one: a. 4.618 kN - Tension b. 8 kN - Compression C. 2 kN - Tension d. 8 kN - Tension