Sub:power electric EX1) A boost converter has an input voltage of 5 V. The average output voltage is15 V and the average load current is 0.5 A. If fs = 25kHz, L = 150 µH and C = 220µF, determine(a)duty cycle(c) inductor peak current (d) output ripple voltage(b) inductor ripple current

Given, A boost converter has , Input voltage (Vin) = 5 volts Output voltage (Vo) = 15 volts Average…

Answered: (a)duty cycle (c) inductor peak current…

Engineering

Electrical Engineering

(a)duty cycle (c) inductor peak current (d) output ripple voltage (b) inductor ripple current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: D1 KH 1SR154-400 V1 + SINE(0 15 1K) Vo R1 2K

A: Diode: It is a semiconductor device that is on in the forward bias condition and off in the reverse…

Q: circuit the diodes

Q: In the circuit shown in the figure; B) When RL = 1Kohm and capacitor C is deactivated, draw VA and…

A: We can redraw the circuit as( Capacitor deactivated) Case 1 Positive half cycle D1→RBD2→FB if…

Q: A 3-phase, half-wave thyristor rectifier with an inductive load is supplied by a three-phase source…

A: Van=120 v phase voltage. firing angle= 40 3 phase Half wave Thyristor Rectifier.

Q: Input waveform Input waveform Output waveform Output waveform The following oscilloscope traces are…

A: We have given The following oscilloscope traces are examples of what? 1) Slew rate distortion 2)…

Q: Q: A single phase Half- wave controlled rectifier is connected to RL load (R=8ohm and L=12mH ), Vs=…

A: Given data, R=8 ΩL=12 mHVS=250 Vf=50 Hzα=40°

Q: Turn off the function generator and build the following circuit. Make sure that the zener diode…

A: If we consider the ideal diodes condition, i.e. 0 voltage drop across the diodes. so, considering…

Q: A single phase fully controlled rectifier has RL load. Write the following a) Draw its circuit…

A: Figure below shows the circuit diagram and the waveforms of a single phase fully controlled halfwave…

Q: Draw the input waveform and output waveform for the circuit given below with proper values marked in…

A: Given, D1 -> Germanium diode, the On-state voltage drop is 0.3 V D2-> Silicon diode, the…

Q: If a half-wave rectifier is used with 117-V rms ac (house mains), the average dc output voltage is…

Q: Q1: ideal diodes are used in the circuit shown in figure. Sketch the output voltage 1Kohm D3…

Q: Sketch and explain the output wave shape for the circuit. The generator signal is a sine wave with a…

A: In this question, We need to Sketch and explain the output wave shape for the circuit. Assume…

Q: A 10 VOLTS PEAK TO PEAK SINUSOIDAL VOLTAGE IS APPLIED ACROSS A SILICON DIODE AND SERIES RESISTOR.…

Q: Q3: A 3-phase half wave-controlled rectifier is fed from 3-phase 400V, 50Hz source and is connected…

A: We are authorized to answer only 3 subparts at a time since you have not mentioned which part you…

Q: QUESTION 11 The voltage signal coming out of the capacitor is with small ripples compare to the…

A: To charge battery from AC supply rectifier (converter) circuits are used. According to supply a…

Q: What is the importance of the charecteristic curve in PN Junction

A: Characteristics of pn junction diode

Q: Zener Diodes are usually working in the zero voltage region O forward biased O reverse biased O…

A: By using the concept of zener diodes we need to answer the correct option for the given multiple…

Q: In the circuit shown in the figure; A) When RL = 5Kohm and capacitor C is switched on, draw VA and…

A: We can redraw the circuit as Here transformer will be step down otherwise diode will get damage.…

Q: A voltage regulator is a device that: O Maintains a fixed DC voltage. Maintains a fixed AC voltage.…

Q: Voltage Regulator using Zener diodes

A: Voltage Regulator- The zener diode voltage regulator is based on a particular characteristic of…

Q: 1) The following is not an example of a Thyristor a) A Silicon Unilateral Switch b) A TRIAC c) A…

Q: What is the frequency of the lowest order harmonic in three-phase full wave converter

A: Only 6k+1 or 6k-1 order harmonics are present in 3 phase full wave rectifer.

Q: + R ww Vg ideal 25V + V

Q: LR phase shift control is used in a controlled rectifier. If the value of the inductor is 100 mH,…

Q: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 μF; average load voltage…

A: we need to determine ripple factor and average load current.

Q: For a full-wave controlled rectifier, find out the RMS output voltage

A: Given data Vm = 220

Q: f combination circuits

A: It is a combination of a series circuit and parallel circuit in which some elements are connected in…

Q: Q17: A fully-controlled three-phase bridge rectifier circuit is modified by placing a commutating…

Q: In a half wave rectifier, the sine wave input is 300sin300t. The average value of output voltage is?…

A: The solution can be achieved as follows.

Q: Q5. For the following center tapped transformer, show the waveform across each half of the secondary…

A: The waveform across each half of the secondary winding is shown by Vac & Vbc waveforms in the…

Q: 5. In the following circuit, Vin is a sinusoid AC input voltage which has a peak voltage of 15v.…

Q: A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system.…

A: The solution is given below

Q: In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R…

A: Given data: Frequency f=60 Hz Resistance R=100 Ω Capacitance C=1000 microfarads Secondary RMS…

Q: b) A sine voltage trace displayed on a screen is shown in figure5. The x axis is 1unit=50 ms and y…

Q: the rms value of half wave rectifier symmetrical square wave current of 2Ais 1.414 O 1 O 0.707 O…

A: Part (A) So Irms = 1.414 A

Q: In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases.…

A: Choose the correct option In the half wave Rectifier with fliter, If the capacitance value increase…

Q: In 3-phase full-wave controlled rectifier of six thyristors with an inductive load, if thyristor T1…

A: The explanation is as follows.

Q: Q1: ideal diodes are used in the circuit shown in figure. Sketch the output voltage IKohm D3…

Q: What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform M₁ (b) O Unipolar O…

A: In case of unipolar pulse width modulation taken two sinusoidal modulating signal in outof phase…

Q: A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis…

A: x axis: 1 unit=40 ms 2 unit=2×40=80 msy axis: 1 unit=4 V 1.5 unit=1.5×4=6…

Q: Q1: ideal diodes are used in the circuit shown in figure. Sketch the output voltage 1Kohm D3…

Q: Converter control in solar photovoltaic

A: The photovoltaic effect, which is the conversion of light (photons) to electricity (voltage), gives…

Q: 7. The transformer is a 10:1 each diode drops 0.7V in the forward direction. What is the output…

Q: Design electronic voltage regulator circuit using zener diode of 24 V DC.

Q: In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases.…

A: In this question we need to verify the given statement is true or false

Q: 14.3 V Answer the following questions, since the minimum voltage value to transmit the zener diode…

Q: A single-phase controlled rectifier bridge consists of one SCR and three diodes as shown in figure.…

A: First draw the output voltage waveform and than find the average output voltage. Using average…

Q: In semiconductor lasers the lasing threshold current tends to decrease as temperature increases.…

A: To find out true or false

Q: write the procedure to design phase lead compensator

Q: A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load…

A: Given data : The given source voltage Vs=100sin277tV The given ammeter reading i=20A

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Sub:power electric

EX1) A boost converter has an input voltage of 5 V. The average output voltage is
15 V and the average load current is 0.5 A. If fs = 25kHz, L = 150 µH and C = 220
µF, determine
(a)duty cycle
(c) inductor peak current (d) output ripple voltage
(b) inductor ripple current

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform A (b) 44444 F -V O Unipolar O Bipolar 000
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
/1/A single-phase, half-wave, controlled has a source 220V at 50 HZ and is eding a load R=2002 and L=25 mH, the firing angle a=60° and the current tinction angle ß=225° Determine the average load voltage and current. O Determine the rms load voltage and current. led rectifier the value of the output
The average (DC) value of a half-wave rectified voltage with a peak value of 200 V is: a. 63.7 V b. 127.3 V c. d. OV 141 V 2. Voltage regulation is determined by: a. load current b. Zener current and load current c. changes in load resistance and output voltage d. changes in no-load voltage and full-load voltage When a 60-Hz sinusoidal voltage is applied to the input of a full-wave rectifier, the output frequency is: a. 120 Hz b. 60 Hz c. 240 Hz d. 0 Hz
(C) Q/ Determine and find dc level output ? the vo and sketch wave form, Vi 20 Vo 20 22/ Draw input is aud the the claipper circuit when the Sinwave with (p-p) Cn 20U) diode (si) connected in Series
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
7) sine wave. Sketch the waveform (1 period is enough) for the resulting Vout- What are its positive and negative peak values? (AVforward,ideal = 0) For each of the ideal-diode circuits below, the input Vin is a 1kHz 5-V peak a) b) Vin Vaut Vin Vaut 1kN 1kN c) c) Vin Vout Vin Veut 1kN 1kN e) f) Vin 1kN Vaut Vin 1kN Vout 太太

A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The load is purely resistive of value 52. The DC and RMS output voltages are respectively equal to: Secondary 太D太D,太D, 太D。太De太D, b. Select one: O a. 180V, 240.2V O b. 514.6V, 515.04V O c. 180V, 197.2V O d. 220V, 249.2V
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to c 20:5A L VI-DC20V 220V omsh T 0.01 F 0.02 F 0.0167 F None of the above euer
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Mr. Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit