a. Find the mathematical expressions for the transient behavior of vc. ic, and vR for the circuit of Fig. Q4 D. How much time must pass before it can be assumed, for all practical purposes, that ic = 0 A and vc = E when the switch is moved to position L. Plot the curves of vo G and ve %3D volts? + VR 季 %3! ic 8 kN 40 V 4 uF Vc Fie Od

a. Find the mathematical expressions for the transient behavior of vc. ic, and vR for the circuit of Fig. Q4 D. How much time must pass before it can be assumed, for all practical purposes, that ic = 0 A and vc = E when the switch is moved to position L. Plot the curves of vo G and ve %3D volts? + VR 季 %3! ic 8 kN 40 V 4 uF Vc Fie Od

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A zener shunt regulator employs a zener diode for which VZ = 10.1 V at IZ = 10 mA while rz = 20 Ohm.The available supply voltage (VS) is 15 V, R = 200 Ohm, and the load resistance (RL) = 1.0 k a) Find VZ0. b) Calculate the output voltage (VO) (hint: The derived expression for VO can be used here without proof) c) If RL is changed so that the load current (IL) is increased to 20 mA, what is the value of the output voltage (VO)?
Using a positive Clamper with positive biasing voltage Circuit, with an AC voltage of Vi = 20v with a frequency of 60hz, a value of 500n for the Capacitor, a silicon diode, biased voltage voltage of 5 volts and a resistor with the value of 300 ohms. Find the current on the resistor at a simulation of 20ms in mA. Vm 2Vm R V,m Vo -Vm V, Input Waveform Output Waveform Positive Clamper with positive reference V, www
The diode in the circuit shown has a reverse saturation current of 1.5 x 10-¹4 A and an ideality factor of 1.1. Assume the circuit is operating at 27°C. a. Determine VOUT. b. What is the small signal model of the diode under these conditions? You may neglect the parasitic capacitance across the diode junction and the resistance of the semiconductor material outside the diode junction. C. 2 V ww 1ΚΩ ▷ -1₁ VOUT Use this small signal model to approximate the peak-to-peak value of the AC component of VOUT if a 1 mV RMS sinusoidal signal is added to the 2 V DC source.
4. A conductor carries a current that maybe regarded as equivalent to the sum of two components, one of them being a continuous direct current of 4.2 amp and the other a superimposed full-wave rectifier current. If the latter has a maximum value of 6.4 amp, calculate the average current in the wire if (a) both components have the same direction, (b) the two components are oppositely directed?
Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that clamps the positive peaks to -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. List any constraints that should be observed in selecting component values. Be sure to label the terminals across which the clamped output waveform vo(t) appears.
Consider a three-phase diode rectifier supplying a R = 10 Ω DC load. The supply systemis 440 VLL and 60 Hz. A) What is the value of the average (DC) current across the load?B) Compute the value of an inductive filter (L) to be added in series with the resistiveload to limit the rms value of the lowest order current harmonic to 1% of the DC currentvalue. Note: 2 /[( 1)( 1)] Vdch = Vdc0 h − h + (in rms).
) For the following circuit, answer the following questions given that : Vz = 10 V, Iz= 25 mA, IzK= 1mA, Zz =72, PD(max) = 1 W at 50 °C. RA (N)=500 Determine the minimum and the maximum input voltages Vin (min), VIN (max) that can be regulated by the zener diode. Also, determine the line regulation. a) If a load resistor is connected, determine the minimum value of this load resistror R1(min) that can be used when VIN is set at 15 V. b) If the Zener derating factor is 2.8 mW/C, determine the maximum power the zener can dissipate at a temperature of 80 C. RA VIN VOUT
Consider the circuit given in Figure (Q4). Let V, = 0.8 V and R = 100 0, find: a) The value of C that results in a ripple voltage not larger than 1 V peak-to- peak. b) The DC voltage at the output c) The current through the load d) The diodes' conduction angle D, 12V (ths) 6. HZ R + Figure (Q4)
Q 2) A single phase half-wave uncontrolled rectifier with RL load is shown With R=1002, La 0. 1H w-377rad/s and V 100V, Determine: a) An expression for the load current i(t). b) The value of the current at t3D16 ms. c) The average load current (1C WLialx197=ア7.9 =121 V, = V, sinfar) 17.2 0.360
R2=1kiloOhm, Voltage Source=10Vpk at 1kHz frequency, R3=1kiloOhm and zener diode has 5V breakdown potential R1 www 1k0 D1 Vo V1 5V 10Vpk 1kHz R2 1k0 a.) Plot the Output Waveform Vo. b.) Explain the output waveform at + input cycle. c.) Explain the output waveform at - input cycle.
Question 6 ac Load Supply Figure Q6a : Rectifier Circuit a) For the circuit shown in figure Q6a Identify the type of rectifier ii) i) Sketch the output voltage waveform if the load was purely resistive when the thyristor is triggered at a degrees (0 sas 180° ). Determine an expression for the average voltage, VAv, seen across the load. iii) 1 You are given that Vav V sin Ad0
A conductor carries a current that is equivalent to a 5-amp continuous current in one direction and a superimposed full-wave rectifier current in the opposite direction. What is the maximum value of the latter if the average conductor current is zero?