A wall with an area of 10 m2 is made of a 2cm thickness of white pine (k=0.113 W/m-deg C) followed by 10 cm of brick (k=0.649 W/m-deg C). The pine is on the inside where the temperature is 30 deg C while the outside temperature is 10 deg C. Assuming equilibrium conditions exist, what is the temperature at the interface between the two metals? Select the correct response: 15.65 deg C

A wall with an area of 10 m2 is made of a 2cm thickness of white pine (k=0.113 W/m-deg C) followed by 10 cm of brick (k=0.649 W/m-deg C). The pine is on the inside where the temperature is 30 deg C while the outside temperature is 10 deg C. Assuming equilibrium conditions exist, what is the temperature at the interface between the two metals? Select the correct response: 15.65 deg C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
A particular device needs to be made that will experience a change in temperature of 100 °C. Two materials are being considered: copper (α = 1.7*10-5 °C-1) and steel (α = 1.3*10-5 °C-1). If made of copper, the device would be 2 m in length. If made of steel, the device would be 2.615 m in length. Which device would experience more thermal expansion?
A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the other end is at x = 3. The thermal diffusivity of the bar is k = 0.4. The bar's initial temperature f(x) = 300 degrees Celsius. The ends of the bar (x = 0 and x = 3) are then put in an icy bath and kept at a constant O degrees C. Let u(x, t) be the temperature in the bar at x at timet, with t measured in seconds. Find u(x, t) and then u7 (2, 0.1). Put uz (2, 0.1) calculated accurately to the nearest thousandth (3 decimal places) in the answer box.
Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with specified surface temperature with heat generation. Case 3: A rod with specified surface temperature with variable thermal conductivity k=k(1+BT), ß: is constant. The quadratic temperature profile T(r)= f(r) will be in:
Please solve Correctly as Answer is already given. Don't Copy
A brass plug is to be placed in a ring made of iron. At 20°C, the diameter of the plug is 8.755 cm and that of the inside of the ring is 8.741 cm. They must both be brought to what common temperature in order to fit? Given : Required : Illustration: Solution: final answer:
Using Ritz technique, determine the temperature distribution in the fin. T=20 °c, h=0.3 w/cm² °c, k=4 w/cm °c. Assume free end is open to the atmosphere
I need the answer as soon as possible
3-52 A 4-m-high and 6-m-wide wall consists of a long 18-cm X 30-cm cross section of horizontal bricks (k = 0.72 W/m . °C) separated by 3-cm-thick plaster layers (k = 0.22 W/m . °C). There are also 2-cm-thick plaster layers on each side of the wall, and a 2-cm-thick rigid foam (k = 0.026 W/m - °C) on the inner side of the wall. The indoor and the outdoor temperatures are 22°C and −4°C, and the convec- tion heat transfer coefficients on the inner and the outer sides are h₁ = 10 W/m² . °℃ and h₂ = 20 W/m². °C, respectively. Assuming one-dimensional heat transfer and disregarding radi- ation, determine the rate of heat transfer through the wall. Foam Plaster Brick 1+₂+18 2 FIGURE P3-52 18 cm N 1.5 cm 30 cm 1.5 cm
In the figure below, it is known that the thermal conductivity of k1 = 0.06 W/mK, k3 = 0.04 W/mK, and k4 = 0.12 W/mK. The thickness of the layers is L1 = 1.50 cm, L3 = 2.8 cm, and L4 = 3.50 cm. Known temperatures T1 = 30°C, T12 = 25°C, and T4 = -10°C. Energy transfer through walls is constant. How much is T34?
A solid 0.48-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 20 in., its elastic modulus is E = 30000 ksi, and its coefficient of thermal expansion is a = 7.2 x 10-6 in./in./°F. Determine the temperature increase AT %3D %3D that will cause the rod to buckle. A L B Answer: AT =
The initial temperature of a 50 cm long silver wire is 50 °C. The circumference of the wire in question is completely insulated, but both ends are kept at a temperature of 0 °C (zero degrees Celsius). Obtain the heat conduction along the wire as a function of time and position and, taking a single term in the solution, determine how many degrees Celsius the temperature in the middle of the rod will be after 7 minutes. (For silver wire, α=1.70 cm2/s.)