You may have noticed that bridge decks are often built with expansion joints that permit the deck to expand and contract with changes in temperature. A bridge deck is to be made from steel, a=12.3x106 /K) and is expected to operate over a temperature range -(-36)°C to 50°C. If the ramps to the bridge are precisely 10.8 meters apart and do not move with changes in temperature, and the deck must be sized such that no axial stress is developed due to thermal expansion: a) The length of the bridge deck measured at 20°C must be no longer than m (calculate to three decimal places. i.e. the nearest mm) b) The sum of the gaps at each end of the bridge at (-36)°C will be mm

You may have noticed that bridge decks are often built with expansion joints that permit the deck to expand and contract with changes in temperature. A bridge deck is to be made from steel, a=12.3x106 /K) and is expected to operate over a temperature range -(-36)°C to 50°C. If the ramps to the bridge are precisely 10.8 meters apart and do not move with changes in temperature, and the deck must be sized such that no axial stress is developed due to thermal expansion: a) The length of the bridge deck measured at 20°C must be no longer than m (calculate to three decimal places. i.e. the nearest mm) b) The sum of the gaps at each end of the bridge at (-36)°C will be mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need these 3 parts answered TRUE or FALSE.
You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in with an accuracy of plus/minus .25 tolerance. You end up with a 10 in rod but what is the tolerance? (hint: rely on the basic principle of tolerance
I need question 10 answered please and thank you. Question pertains to the print provided and also the sequence of operations listed in the directions.
please provide the following: speed rate, deep of cut and measurements of a meat mallet.
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…