A voltage generator with vg(t) = 5 cos(2л x 10°t) V and internal impedance Zg= 50 2 is connected to a 50-2 lossless air-spaced transmission line. The line length is 5 cm and it is terminated in a load with impedance ZL (100-j100) 2. Find = (b) Zin at the input to the transmission line. (c) the input voltage and input current I. (d) The average power delivered to the load

A voltage generator with vg(t) = 5 cos(2л x 10°t) V and internal impedance Zg= 50 2 is connected to a 50-2 lossless air-spaced transmission line. The line length is 5 cm and it is terminated in a load with impedance ZL (100-j100) 2. Find = (b) Zin at the input to the transmission line. (c) the input voltage and input current I. (d) The average power delivered to the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.8P

See similar textbooks

Similar questions

7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
8. A transmission line has a characteristic impedance of 500 and a resistance of 0.1 02/m. If the line is distortion less, the attenuation constant (in Np/m) is (a) 500 (b) 5 (c) 0.014 (d) 0.002
A lossless T-junction power divider has a source impedance of 50 2. Find the output characteristic impedances so that the output powers are in a 2:1 ratio. Compute the reflection coefficients seen looking into the output ports.
b. Determine what is the necessary length and characteristic impedance of a cable to be used as a quarter-wave matching transformer so that it can eliminate the standing waves and subsequently provide a matched condition for a 180 O resistive load fed from a 45 0 transmission line. This condition is to exist for a frequency of 95 MHz. Given a velocity factor = 1.0.
5. Two cascaded lossless transmission lines are terminated by Z₁-2502, as shown below.. a) Calculate the reflection coefficient and the standing wave ratio at the load, i.e., the CC' terminal. b) Determine the characteristic impedance of the quarter-wavelength transformer, Zol, to match the cascaded line to a 6492 generator. B A- A'. Zol 11= 2/4 B' Zo2=75 92 12=32/4 C C ZL=2592
A 702 high-frequency lossless line is used at a frequency where 2 = 80cm with a load of 140+j91 2 a. Calculate the reflection coefficient and the SWR b. Determine the distance to the first voltage minimum from the load c. Determine the distance to the first voltage maximum from the load d. Calculate the impedance at the point where maximum voltages occur
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. Determine 1)The capacitance in uF/km without effect of ground 2)The capacitance in uF/km with effect of ground
Qd) A voltage generator with Ve(t) and impedance Zg 50 2 is connected to a 50 2 air lossless TL at 500MHZ. The line length is (4/10)2 m and it is terminated in a load with impedance ZL=(50-j60) Q. Find: (a) Line Parameters. (b) T, and VSWR at the load. (c) (d) Zin at the input to the TL. Return loss.
3-8. A lossless transmission line is terminated in an open circuit. The sending end is ener- gized by a generator which has an open-circuit output voltage of V, (rms) and an inter- val impedance equal to the characteristic impedance of the line. Show that the sending- end voltage is equal to the output voltage of the generator. 3-9. A lossless transmission line has a characteristic impedance of 300N and is operated at a frequency of 10 GHz. The observed standing-wave ratio on the line is 5.0. It is pro- posed to use a short-circuited stub to match a pure resistor load to the line. a. Determine the distance in centimeters from the load to the place where the stub should be located. (Two possible solutions.) b. Find the length of the stub in centimeters. (Two possible solutions.) 3-10. A lossless line has a characteristic impedance of 50 N and is loaded by 60 - j60 N. One stub is at the load, and the other is 3A/8 distance away from the first. a. Determine the lengths in wavelength of…
The impedance of the 500 km long transmission line is Z = 0.1 + j * 0.4 ohm / km. At the end of the line, 988.1 A current is drawn under 400 kV interphase voltage. The angle of the current is -68. It is 6 degrees. With the short transmission line equations, the amplitude value of the phase neutral value of the busbar voltage to which the generator at the beginning of the line is connected is given correctly. A) 231.34 B) 52.35 C) 400 D) 380.28 E) 388.57
1. a. A purely reactive load impedance Z₁ =jX terminates a transmission line. Prove that the reflection coefficient magnitude |K| is always unity, assuming the characteristic impedance Zo is real. What is the VSWR of the line in this case? b. Consider the transmission line in the figure. i. Determine the SWR on transmission line ii. The input impedance If=102, find I, in the figure. WC 100/0*V] 20 922 Air, lossless Z-50 £2 2.72 40 2 ele 3002