A tube with outer diameter i5mm and inner diameter 10mm, is to be manufactured bydirect extrusion. The billet has a diameter of Do and a length of 200mm. The product isextruded at a speed Vf Assume deformation efficiency 80% and material followsO =110(7) N / mm The extrusion pressure and power are 20 MPa and 300KW,respectively. Calculates:c) Extrusion force in KN?d) The speed Vf?e) The tube final length?) If the power cost is 2 SR/KW.Hr what is the production cost of producing 50 barshaving 2-meters length each from the same cross-section?

Given:The outer diameter of the tube, D = 15 mmThe inner diameter of the tube, d = 10 mmThe billet…

A tube with outer diameter i5mm and inner diameter 10mm, is to be manufactured by direct extrusion. The billet has a diameter of Do and a length of 200mm. The product is extruded at a speed Vf Assume deformation efficiency 80% and material follows =110(7) N / mm² The extrusion pressure and power are 20 MPa and 300KW, respectively. Calculates: c) Extrusion force in KN? d) The speed Vf? e) The tube final length? ) If the power cost is 2 SR/KW.Hr what is the production cost of producing 50 bars having 2-meters length each from the same cross-section?

A tube with outer diameter i5mm and inner diameter 10mm, is to be manufactured by direct extrusion. The billet has a diameter of Do and a length of 200mm. The product is extruded at a speed Vf Assume deformation efficiency 80% and material follows =110(7) N / mm² The extrusion pressure and power are 20 MPa and 300KW, respectively. Calculates: c) Extrusion force in KN? d) The speed Vf? e) The tube final length? ) If the power cost is 2 SR/KW.Hr what is the production cost of producing 50 bars having 2-meters length each from the same cross-section?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A billet 75mmlong and 25mmin diameter is to be extruded in a direct extrusion operation with extrusion ratio rx = 4.0. The extrudate has a round cross section. The die angle (half angle) = 90° The work metal has a strength coefficient = 415 MPa, and strainhardening exponent = 0.18. Use the Johnson formula with a = 0.8 and b = 1.5 to estimate extrusion strain. Determine the pressure applied to the end of the billet as the ram moves forward
A planned extrusion operation involves cold-rolled steel at 1000°C_with an initial diameter of 110 mmand a final diameter of 20 mm .Two presses, one with capacity (extrusion force) of 20 MN and the other with a capacity (extrusion force) of 7 MN , are available for the operation. Is the smaller press sufficient for this operation? K"=35x10*3 N (Hint: Calculate the extrusion force and compare it to the available two presses]
Extrusion calculation: (1) Calculate the extrusion force ( N or mega newton) required for round billet of 70-30 brass which is extruded at 675 °C. The diameter Db = 100 mm and extrusion diameker De= 30 mm. Assume k = 250. (2)Sketch the problem? %3D
A billet 100 mm long and 40 mm diameter is to be extruded in a direct extrusion with final diameter of product 32 mm. The semi die angle is 60°. The work metal has a strength coefficient 500 Map, and strain hardening 0.2 use the Johnson formula with a=0.8 and b=1.45 to estimate the extrusion strain. Determine the pressure applied to the end of the billet as the ram moves forward.
A 3in long and 1in diameter billet is extruded in a direct extrusion operation with an rx = 4.0. The extrusion has a cross section. The angle of the die (half angle) is 90o. The work metal has a resistance coefficient of 60ksi and a strain hardening exponent of 0.18. Use Johnston's formula with a = 0.8 and b = 1.5 to estimate the extrusion stress. Determine the pressure applied to the end of the billet when the piston moves forward.
You have been asked to work on some design problems and technically support the team working on extrusion and forging operations: 1) The team are extruding a billet that is 80 mm long with diameter of 40 mm is directly to a diameter of 20 mm. The extrusion die has a die angle of 75°, see Figure 1. For the work metal, K = 600 MPa and n = 0.25. In the Johnson extrusion strain equation, a = 0.8 and b = 1.4. Remaining billet length 75 Ram pressure, p D. Dr Figure 1: Extrusion process. Determine the following design parameters: (a) Extrusion ratio. (b) True strain (homogeneous deformation). (c) Extrusion strain. (d) Ram pressure at L= 80, 40, and 10 mm. (e) Draw the relationship between the ram pressure and billet length and discuss the results. What are your recommendations to dccrcase the required ram pressure?
The team is extruding a billet that is 80 mm long with diameter of 40 mm is directly to a diameter of 20 mm. The extrusion die has a die angle of 75°, see Figure 1. For the work metal, K = 600 MPa and n = 0.25. In the Johnson extrusion strain equation, a = 0.8 and b = 1.4. Remaining billet length 75 Ram pressure, p Do Figure 1: Extrusion process. Determine the following design parameters: (a) Extrusion strain (b) Ram pressure at L = 80, 40, and 10 mm. (c) Draw the relationship between the ram pressure and billet length and discuss the results. What are your recommendations to decrease the required ram pressure?
Calculate (1) die pressure distribution and (2) forging force for plane strain forging (open die forging). Assume yield strength of the material is Y, and yielding criterion is von Mises. ho 2Lo h Forged to 2L xdx L 'x+value Note: Assume Zo Constant Plane strain Die pressure distribution h L L Die pressure distribution h MATERIAL L dx -(-1) Friction Hill Y L When 0; =Y P=Y' = Calculate forging force X L dF elemental volume Average pressure
A brass billet is to be extruded from its initial diameter of 100 mm to a final diameter of 50 mm, working temperature is 700 degrees celsius and extrusion constant is 250 MPa. Find out the force required for extrusion?
A billet 100 mm long and 30 mm in diameter is to be extruded in a direct extrusion operation with extrusion ratio r, = 3.5. The extrudate has a round cross section. The die angle (half angle) = 60°. The work metal has a strength coefficient = 720 MPa, and strain hardening exponent = 0.17. Use the Johnson formula with a = 0.8 andb= 1.2 to estimate extrusion strain. Determine the following: 1. Diameter of the extrudate = mm 2. Butt volume = mm3 3. Actual extrudate length = mm 4. The pressure applied to perform the extrusion process = MPa 5. Ram force = N.
During a direct extrusion process for a billet with 5 in long and diameter 2.5 in to 1.6 in. For the work metal, strength coefficient is 75000 Ib/in, and strain hardening exponent is 0.4, also the die angle of extrusion is 90. In Johnson extrusion strain equation a = 0.8, and b= 1.5. Determine: (a) extrusion ratio (b) true strain (c) extrusion strain, and (d) ram pressure at length 5, 4.2, 2.3,1.5,and 0 in.
A round billet made up of beryllium, 200 mm in diameter is extruded at 900°C to a diameter of 100mm. The extrusion constant is 200MPA. The extrusion force (in MN) required is