A triangular trough whose the edges are 5, 5, and 8 m long is place vertically  in water with its longest edge uppermost, horizontal, and 3 m below the  water level. Calculate the force on a side of the plate. A.235.2 kN B. 470.4 kN C. 940.8 kN D. 1,881.6 Kn

Q: An engine drives a machine. The torque equations is given below. The moment of inertia of the…

A: Write the given data with suitable variables:   I=54 kg-m2N=300 rpmθperiodθp=2π

Q: Q3/ A. Show with plot the effect of temperature and strain rate on the mechanical properties of PMMA…

A:

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 70 m below…

A:

Q: The rigid post in Figure 1 has a cable connected to the floor at point D, which generates a tension…

A: Given data, Applied force in cable CD, FCD = 1.2 kN Coordinate of point C = (-1.5, 0, 4.5) m…

Q: 1. Within a cubic unit cell, sketch the following directions: [110], [121], [0Ī2], [123], [103]

A: For solution refer below images.

Q: Which of the following statements about the axial deformation formula is FALSE? a. The formula is…

A: Statement (a) is false about the axial deformation formula. The formula is not applicable at points…

Q: A steel pipe (K=45.0 W/mK) having a 0.05m O.D. is covered with a 0.042 m thick layer of magnesia (K…

A:

Q: Consider the cantilever beam below, which is machined from a steel with an Elastic Modulus of 200…

A:

Q: Problem 2-46 A weather report indicates the barometric pressure is 28.54 inches of mercury. What is…

A: Given data: h=28.54 in=0.724916 m Need to determine the atmospheric pressure.

Q: mechanism question: degree of freedom using kutzbatch equation in

A:

Q: How will I get the approximated Zmix here from the generalized compressibility chart if I have Pr=…

A: How will I get the approximated Zmix here from the generalized compressibility chart if I have Pr=…

Q: Help needed with finding the auxiliary view for 1 and 2. For 1 it's for surface C, for 2 it's for…

A: ghfgsdfsdfsdfsdffghfgsdfsdfsdsfasdasdasdasdghghghhghghhhghghghghghjsdfsdfsdfsddfssdfsdfsdfsdfd

Q: Write the vector expression for the acceleration a of the mass center G of the simple pendulum in…

A: Given that: r = radius = 3.2 ft θ = 69o θ˙ = ω = angular velocity = 1.52 rad/s θ¨ = ω˙ = α = angular…

Q: A spring has a stiffness of 600 N/m, if a 4 kg block is attached to the spring, pushed 500 mm above…

A: Givenk=600N/mm=4kgs=500mm=0.5m

Q: Take a look at the THREE (3) stages of technology acquisition.

A:

Q: A reheat-regenerative Rankine cycle receives steam at 8.0 MPa, 300 °C and exhaust at 0.01 MPa. Steam…

A: Given data, Inlet condition of steam turbine is 8 MPa and 300 °C To determine:- 1) Percentage of…

Q: A wind turbine is rotating at 15 rpm under steady winds flowing through the turbine at a rate of…

A: Given:Speed of turbine, N=15 rpmMass flow rate of air, m=42,000 kg/sTip velocity of turbine, v=250…

Q: Two cylinders are connected by a piston. Cylinder A is used as a hydraulic lift and pumped up to 500…

A: Given data Pressure at A = 500 kpa Mass of piston = 25 kg Find the pressure at B.

Q: Look up the furnace size and the size of the air-conditioning unit in your own home or apartment.…

A: Given Furnace Air conditioner To find Investigation for SEER and AFUE

Q: water is flowing in a 2 inch pipe at a velocity of 0.2 m/s. what pipe size in inches will double the…

A: Given data as per the question diameter of pipe =2 in =0.0508 mvelocity of water =0.2 m/s

Q: hafts are of same length and same material. The diameter and maximum shear s second shaft is twice…

A: Given data:Material of both shaft is same,Length of both shafts is same=LDiameter of 2nd…

Q: Problem 12.129 The car starts from rest at s = 0 and increases its speed at at = 8 m/s². (Figure 1)…

A:

Q: Find the degree of freedom of the mechanisms in Fig.: below by using Kutzbach equation D 8/3 2 Bo…

A:

Q: Find the total work done on the 12.0 N block if there is no friction between the table and the 20.0…

A: Givendisplacement s=75cm=0.75m

Q: points D. E and F are at the mic wen p-4 m.q-2m and r 4 m, identify all the possible position…

A:

Q: a rectangular strip of metal 18 cm wide is to be bent into a trough that has a rectangular cross…

A: Givenrectangular strip of metal width w= 18 cm the cross sectional area A=29 cm2

Q: 3. A pair of bevel gear have a 1:1 velocity ratio, a pitch diameter of 8 in, a face of 1 % in and…

A:

Q: 3. A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to…

A:

Q: Figure 1.5m 2.5m Part A Determine the magnitude of the moment of the force F = {50i- 20 j-80k} N…

A: Given that: F→ = 50i^ -20j^ - 80k^N Under the given condition, it is required to determine the…

Q: The figure below shows a Venturi meter for measuring the water flow rate through a pipe. The…

A: GivenA1=0.01m2A2=0.006m2S.G=1.4h=0.8mg=9.81m/s2ρw=1000 kg/m3

Q: A frame supports both a linear distributed load and a concentrated moment, as shown in the figure…

A: Given data  q= 780 N/m Mc = 57 N-m L1 = 4m L2 = 1.5 m L3 = 11 m Find the internal loading at e and…

Q: A NIO-20 mot% Mgo ceramic is allowed to solidify. (See the figure below.) Temperature (°C) 2800 2600…

A: (a) Determine the composition (in mos MD) of the first sold to form   (b) Determine the composition…

Q: R(acetylene) = 59.35 ft-lbf/lbm-R Answer: a. b. V = _% mass

A: Given-Information:- Diameter, d = 6 inches = 0.5 ftLength, L = 40 inches = 3.333 ftPressure,P1 =…

Q: You want to figure out whether it is safe to touch the outsid surface of the pipe in question. Here…

A: GivenT1=70oCr=0.2mt=12mm=0.012mT2=30oCh=15W/m2Ck=54 W/moCL=1m

Q: Write short note on CRDI diesel engine

A:

Q: Suppose the shaft pictured below has dimensions d = 3 cm, D = 3.3 cm, and fillet radius r = 0.4 cm…

A:

Q: An air-vapor mixture has a dry bulb temperature of 30°C and humidity ratio of 0.015. Calculate the…

A:

Q: What is the rate of heat transfer between hot oil and outside air?

A: Write the given data with suitable variables. Toil=50 °CT∞=20 °Ch°=160 W/m2Kh∞=10 W/m2Kksteel=18…

Q: A force of P = 340 N is applied to the 70-kg cart. The mass center of the cart is at G   Determine…

A: Given:Mass of the cart, m=70 kgForce, P=340 N

Q: LAU P₂ B P4 The I "H Modified differential manometer OH, PA PB = ???

A: Hydrostatic pressure: Hydrostatic pressure is directly proportional to the depth of the fluid. It is…

Q: Box Beam Pin Support at A a B Box Beam b C D a 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3000 lb…

A: Given:a=1.7 ftb=3.4 ftc=2.55 ftP=3000 lbt=0.610 ind=0.820 in

Q: 7. A vessel has a pressure of 200 kPag. The atmospheric pressure is 14.5 psi. Find the absolute…

A:

Q: 1m 10 kN MA Determine the magnitude of the moment M, for equilibrium of the structure. d-04m Answer…

A: Given data as per the question Force applied =10 KN d =0.4 m

Q: The provision for taking up wear of the contact surfaces must be provided. The clutch should have…

A: Friction clutch are devices which works on friction for power transmission.

Q: Kutzbach Equation

A: Since there are multiple parts in the question, as per our honor code we have to answer first three…

Q: Please add units.

A: Unit: It is used as a measure to quantify the quantity identical kind. Every physical quantity has…

Q: How does serpentine robots may affect an industry?

A:

Q: Describe the liquid displacement method to find the density of an irregular solid. Draw a picture to…

A: given; escribe the liquid displacement method to find the density of an irregular solid.

Q: Q9/ A. Differentiate between stress concentration factor, stress intensity factor, fracture…

A:

Q: Hot combustion gases, modeled as air behaving as an ideal gas, enter a turbine at 145 lbf/in.2,…

A: Given Data The gas temperature at inlet is:T1=2700°R The gas temperature at exit is:T2=1620°R The…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.