Help needed with finding the auxiliary view for 1 and 2. For 1 it's for surface C, for 2 it's for surface D.

Q: 1. The appropriate punch size for a blanking operation using to perform a cold-rolled steel (half…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Write a detail note on “Tube Drawing with Mandrels”.

A: Tube drawing is metal forming process in which tube is drawn from a metal stock by plastic…

Q: Explain when we use sectional views and how they are made?

A: Sectional view are required when there is requirment to inspector understand the interior view of an…

Q: Name 2 types of bending?

A: Bending is a type of forming process in which the required object maybe a rod, tube or sheet metal…

Q: QI/ As shown in Fig.(1 ). A horizontal force of P-350N is required to just push the crate up the…

A:

Q: Pressure pads are used in rolling process. Select one: True False

A:

Q: omproper heating of the metal at high temperature in Forging or for a long time causing Brunt and…

A: Heating of the metal at high temperature in forging or for a long time causing Brunt and overheated…

Q: Calculate stamping force to produce washers (1/2 inch outside diameter, 3/8 inside diameter) from a…

A:

Q: Illustrate the basic operations of sheet metal working, indicating on the side of each illustration…

A: Step 1: The basic operation of sheet metal operation is as follows. Shearing Operation Blanking…

Q: Buffing is an example of Riveting is an example of

A:

Q: Identify the type of forming process in which the material is required to pass repeatedly through…

A: Option c is correct.

Q: An automated blanking and forming line is designed to from 2 mm thick sheet, made from 2024…

A: Given:Material:  Aluminum,  temper   - Elongation at :    - Young’s Modulus: (70 GigaPascals)   -…

Q: Explain the disadvantages of Tube Drawing process in which mandrel is not used.

A: The tube drawing process that reduces the tube diameter without using a mandrel is known as tube…

Q: Question # 3 Using ONLY neat sketches show the basic elements and differences in the following: (1)…

A:

Q: When an airplane lands, the wheels of the landing gear first skid over the concrete landing strip…

A:

Q: Write a report and an explanation about Forging with the drawing

A:

Q: What is the difference between rotational motion and linear motion, explain this with the drawing.

A: Linear Motion - A rigid body consist of n particles will be in linear motion if all the particles…

Q: determine the overall fraction of the operation.

A: In a two stage wire drawing operation,   the fractional reduction in the first stage is = 0.4…

Q: * Which defect arises due to small Punch force in sheet drawing operations? O Tearing O Wall…

A:

Q: From the data, determine the size of the punch, for a circular blanking operation

A: As per given question  Size of the blank =30mm Thickness of the sheet=3 mm Radial clearance b/w…

Q: Compare any ten major differences between Drawing process and Extrusion process

A: Following is the differences between Drawing process and Extrusion process- Extrusion Drawing…

Q: 10)A moving mandrel is used in Wire drawing Tube drawing Metal cutting Forging

A: As per given question  We have to choose correct options and explain

Q: Hot forming temperature zone is limited to only 75% of the work piece absolute temperature and it's…

A: Hot forming process refer to the process in which metal is deformed plastically above their…

Q: Q4) Answer the following questions: - A) Compare briefly between the following: i. The direct and…

A: A). (i) Direct Extrusion Indirect Extrusion  A solid ram drives the billet  forward and…

Q: The figure below shows a symmetric plane-strain upsetting process. The process may also be thought…

A: The intiallength of the tube is LiLi=2t+t        =3tThe final length of the tube is LfLf=2t+2t…

Q: 5) Thread rolling is considered the best commercial mass production process that give high…

A: given; (5) thread rolling is considered the best commercial mass production process that give higher…

Q: What are the reasons for developing forming limit diagrams (FLD)? Explain its use.

A: Let is understand in detail about forming limit diagrams.

Q: 4) In progressive forming

A: Option (b) is correct. Parts are formed at the successive stages which are carried out in the same…

Q: 24- Write (True) or (False) and correct the wrong sentences for the following: 1. Chills are used to…

A: 1. Chills are used to increase the heating rate of metal. False correct:-Nichromes are used to…

Q: 7. Please analyze and compare the characteristics of sliding guide and rolling guide.

A: A linear guide (also known as a linear bearing) is a mechanical component that allows relative…

Q: 3) Hot forming temperature zone is limited to only 75% of the work piece absolute temperature and…

A: Ans. 3) The excess temperature may cause the extra grain growth in the material which will alter the…

Q: What is special about an oblique drawing?

A: A type of drawing with the help of which three-dimensional drawings, diagrams, charts, and figures…

Q: Explain the importance of lubrication in wire drawing

A: Wire drawing Wire drawing is the process in which metal is pulled out through die using tensile…

Q: 1. Explain the importance of standards and the principles of free hand in sketching in engineering…

A: The Answer is below

Q: what is Deep Drawing?

A:

Q: a). Briefly explain the rolling process with a neat diagram. b). Differentiate between hot working…

A: Rolling: It is type of manufacturing process which is used to convert metal strip into uniform…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.