A three-stage compressor receives 500 lps of air at 101 kPaa and 27 oC, and discharges at 750 kPaa. Determine a) the power required; b) the pressure at each intercooler; c) the maximum temperature; and d) the heat transferred in each intercooler. e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?

A three-stage compressor receives 500 lps of air at 101 kPaa and 27 oC, and discharges at 750 kPaa. Determine a) the power required; b) the pressure at each intercooler; c) the maximum temperature; and d) the heat transferred in each intercooler. e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter49: Operation, Maintenance, And Troubleshooting Of Chilled-water Air-conditioning Systems

Section: Chapter Questions

Problem 1RQ: How does the compressor lubrication system differ for reciprocating and centrifugal compressors?

See similar textbooks

Similar questions

The following data were obtained from a performance test of a 10 x 9-cm single acting, water jacketed two-stage air compressor: Pressures: Atmospheric, 102 kPaa; leaving first-stage, 634 kPaa; leaving second-stage, 4.20 MPa. Temperatures: Atmospheric, 240C; leaving first-stage, 1080C; entering 2nd stage, 250C; leaving 2nd stage, 1270C Compressor speed, 648 rpm Power input to motor, 5.65 kW Motor and belt efficiency, 81.5% The following are calculated from test data: Air flow rate, 0.387 ??⁄??? Compression exponents: 1st stage 1.15; 2nd Stage, 1.2 Calculate: a) Approximate indicated power b) Power for isothermal compression c) Shaft power d) 1st stage piston displacement e) Actual volumetric efficiency f) Isothermal compression efficiency g) Mechanical efficiency based on the approximate indicated power h) Over-all efficiency of the compressor
a reciprocating compressor handles 1001 cfm
5) An auditorium is designed to seat 4500 people. The ventilation rate is 1.62 x 107 ft3/hr of outside air. The outside temperature is 0oF dry bulb, and outside pressure is 14.6 psia. Air leaves the auditorium at 70oF dry bulb. There is no recirculation. The furnace has a capacity of 1,250,000 Btu/hr. The temperature at which the air should enter the auditorium is most nearly
b) A single-acting, two-stage reciprocating air compressor runs at a speed of 500 rev/min with overall pressure ratio of 20 to 1 has free air delivery of 5.0 m3/min. For the first stage compressor, the pressure and temperature at the end of induction stroke is 100kPa and 27°C, respectively. The intermediate pressure is 500 kPa, and the intercooling process is complete. The clearance volumes of both stages are 5% of their respective swept volumes. The ambient pressure and temperature are at 100 kPa and 27°C, respectively. The index of compression and expansion, n is 1.3. i) Sketch the cycle on a P-V diagram. ii) Determine final delivery temperature of the compressor, C. iii) Determine totalindicated power, kw. iv) Determine volumetric efficiency for the first stage, %. v) Calculate the swept volume of the first and second stage, m2. Take the value of R for air is 0.287 kl/kg.K.
Air with a pressure of 0.1 MPa and a temperature of 25oC with a flow rate of 5.29 kg/minute enters a three-stage reciprocating piston compressor with intercooler. The air is compressed polytropically (n = 1.3) to reach the pressure of 4 MPa. Calculate: a) The amount of heat transferred to each intercooler? b) How much air is needed for cooling in the intercooler if the allowable maximum temperature changes between the inlet and outlet of the intercooler is 8oC?
Q2 Figure Q2, A turbo-compressor supplies power to the air-condition unit (Refrigerant) with 900.0 kw. Calculate the volume per minute of the gas operating through the unit where the density is 1 Ib/ft. Given Data: TH Atmospheric temperature = 520°R Compressor gas temperature = 607°R CP 0.539, J=778J/S, Conversion factor =33000.0 One-hours power = 746 watts. QH R 900.0kw Figure (Q2), Refrigerant unit TL
a.) What are the different types of fans used in air-conditioning systems? Discuss their applications and relative advantages and disadvantages. b.) Air from an air-conditioned room is exhausted into atmosphere through a grill. The quantity of air passes through the grill is 20 cubic meter minute. The duct area leading to the grill is 0.12 m2. The static pressure behind the grill is 3 mm of water. Find the effective area of grill exhausting the air into atmosphere. Take the pressure loss passing through the grill as 0.5 mm of water. Solve both a and b Asap please , I will rate
A 3-stage compressor delivers 0.23 kg/s of air. The suction pressure and temperature are 100 kPaa and 27 ̊C, respectively. The discharge pressure is 1380 kPaa. Intercooler is installed after each stage. Determine compressor work in kW. Ans. 59.07 kW
QUESTION 25 A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m3/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual nuber to find the intermedia pressure ratios is
2) how the efficiency of a compressor can be calculated??
The power requirement of a 3-stage compressor (in kW, two decimal places) in order to supply air at 20 degrees celcius at a rate of 250 cubic meter per hour at a total discharge pressure of 100 psig is ___________. If the efficiency of the compressor is 60%. Give full solution:
QUESTION 26 A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m³/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual nuber to find the intermedia pressure is The intermidiate pressure ratio is (to 3 decimal places), The intermidiate pressure at first, second and third stage in kPa to 1 decimal place are: and respectively. No need to add units