8.5 (A). A flanged coupling having six bolts placed at a pitch circle diameter of 180 mm connects two lengths of solid steel shafting of the same diameter. The shaft is required to transmit 80 kW at 240 rev/min. Assuming the allowable intensities of shearing stresses in the shaft and bolts are 75 MN/m² and 55 MN/m² respectively, and the maximum torque is 14 times the mean torque, calculate: (a) the diameter of the shaft; (b) the diameter of the bolts. [B.P.][67.2, 13.8 mm.]

8.5 (A). A flanged coupling having six bolts placed at a pitch circle diameter of 180 mm connects two lengths of solid steel shafting of the same diameter. The shaft is required to transmit 80 kW at 240 rev/min. Assuming the allowable intensities of shearing stresses in the shaft and bolts are 75 MN/m² and 55 MN/m² respectively, and the maximum torque is 14 times the mean torque, calculate: (a) the diameter of the shaft; (b) the diameter of the bolts. [B.P.][67.2, 13.8 mm.]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hollow aluminum propeller shaft, 30 ft. Ilong with 15 in. outer diameter and an inner diameter…

A: (a) The maximum shear stress, τmax = 3.8 ksi. (b) The angle of twist of the shaft, θmax = 0.052…

Q: A solid shaft of 20 mm radius is transmitting 2.5 kW with the frequency of 50 Hz. Calculate the…

Q: Problem 4

Q: Problem 3. A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the…

Q: A marine type flange coupling is used to transmit 3.75 MW at 150 r.p.m. The allowable shear stress…

Q: A flanged protective type coupling is required to transmit 50 kW at 2000 r.p.m.. Find : (a) Shaft…

A: Since the question asked by you falls in multi-question category, thus according to our guidelines…

Q: maximum shear stress in the shaft

A: Given; Motor driving a solid circular steel shaft transmits, P =40KW Speed,N=500 rpm If the diameter…

Q: Q.1 Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for…

A: Answer: Given, T = 2000Nam = 2000 x 103 N - mm τ= 50 MPa σ t = 90MPa No ,of bohts , N = 6…

Q: Two motors deliver 119 hp each at 1000 rpm to shafts at A and D. The shaft transmits torque through…

A: Data given- Motor deliver = 119 hp N = 1000 rpm Shear modulus = 11 × 103 ksi

Q: 5.1 A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress o: MPa, or…

Q: the torque acting on the shaft; ii) the required external and internal diameters for the shaft;…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a…

Q: A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in…

A: The force on the shaft is 94236.5 N.

Q: The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a…

Q: PROBLEM NO. 1 A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20…

A: Given data: D=40 mmL=533 mmd1=20 mmd2=30 mmτ=80 MPaN=230 rpm Need to determine the maximum power…

Q: 3. A flat annular steel flywheel of outer radius 0.5 m and inner radius 0.125 m with p = 7800…

Q: As shown, a shaft is composed of five cylindrical sections. A motor is attached at F and supplies…

Q: Answer number 2 Good handwriting

A: Established the relation among two stresses as follows.

Q: A concentric shaft AB made of hollow bronze (OD = 100 mm, ID = 80 mm, G = 41 GPa) and solid steel (D…

A: Given:To find:Determine the maximum permissible torque T.

Q: Two parallel shafts connected by a cross belt have the diameters of pulleys 40cm and 60cm…

A: Given D1 = 40 cm D2 = 30 cm c = 6 m To find Verify whether belt alteration is required.

Q: A flange coupling having six bolts on a pitch circle radius of 300 mm connects two hollow shafts…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa…

Q: Six 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel and six 20 mm diameter…

A: Given data: n1=n2=6d2=30 mmd1=20 mmR2=370 mmR1=260 mmτ1=28GPaτ2=84 GPa Need to determine the torque…

Q: 105 r.p.m. carrying a load of 150 kN; and 2. number of collars required. (uniform) and the…

A: Intensity Pressure is a group of two forces. Only at the joints are forces applied. The forces in…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

8.5 (A) A flanged coupling having six bolts placed at a pitch circle diameter of 180 mm connects two lengths of
solid steel shafting of the same diameter. The shaft is required to transmit 80 kW at 240 rev/min. Assuming the
allowable intensities of shearing stresses in the shaft and bolts are 75 MN/m² and 55 MN/m² respectively, and the
maximum torque is 1.4 times the mean torque, calculate:
(a) the diameter of the shaft;
(b) the diameter of the bolts.
[B.P.] [67.2, 13.8 mm.]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt circle. What diameter of bolt should be used if the power transmitted is 26.5 kW and the design shearing stress of the bolt is 12 MPa?
ي
2. Two shafts, one solid the other one hollow, are connected end to end by means of a coupling in which there are 8 screws on the pitch diameter D = 250 mm. The solid shaft has diameter d = 50 mm and transfers the power P = 500 kW at 75 rev/s. The external diameter of the hollow shaft is dex = 75 mm. %3D Note: All parts of the system must be equally strong, and able to transfer the required power Calculate: (a) The internal diameter d; of the hollow shaft (b) The diameter of the bolts d, connecting the two shafts (c) If the hollow shaft has to be replaced by a rectangular hollow cross-section with outer dimensions b xh and uniform wall thickness of 4 mm. Calculate the values b, h while following the request to keep h = 2b
8.9 (A/B). A solid steel shaft of 200 mm diameter transmits 5 MW at 500 rev/min. It is proposed to alter the horsepower to 7 MW and the speed to 440 rev/min and to replace the solid shaft by a hollow shaft made of the same type of steel but having only 80% of the weight of the solid shaft. The length of both shafts is the same and the hollow shaft is to have the same maximum shear stress as the solid shaft. Find: (a) the ratio between the torque per unit angle of twist per metre for the two shafts; (b) the external and internal diameters for the hollow shaft. [L.Mech.E.] [2.085; 261, 190 mm.]
A flanged bolt coupling consists of six 2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 6000 psi in the steel or 9000 psi in the aluminum? Assume Gst = 12 × 106 psi and Gal = 4 x 106 psi.
3. Find the power that can be safely transmitted by a flange type shaft coupling, if it has four equally spaced studs all at a radius of 50 mm from the shaft centre. The mean stud diameters are 12.5 mm, and each stud has a maximum safe working shear stress of 86 MPa. The shaft rotates at 3600 rpm.
A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the allowable shearing stress is 300 Mpa and key width is 10 mm ,determine the length of key.
None
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.