3. A 3 rectangular gate is hinged at the top edge A and is restrained by a fixed ridge at B. Determine the hydrostatic force exerted on the gate by the 5 m high water and the location of the line of action of the force. Water Mercury 2m + 3m A Gate Assume width = 1 I to the pa horio pressure and temperature are 101k Pa and 15°C.

3. A 3 rectangular gate is hinged at the top edge A and is restrained by a fixed ridge at B. Determine the hydrostatic force exerted on the gate by the 5 m high water and the location of the line of action of the force. Water Mercury 2m + 3m A Gate Assume width = 1 I to the pa horio pressure and temperature are 101k Pa and 15°C.

Name: 3. A 3 rectangular gate is hinged at the top edge A and isrestrained
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. A 3 rectangular gate is hinged at the top edge A and isrestrained by a fixed ridge at B. Determine thehydrostatic force exerted on the gate by the 5 m highwater and the location of the line of action of the force.WaterMercury2m+3mABGateAssume wid

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
2. The tank shown contains alcohol (SG=D0.78) and covered by a circular plug 1.2 m in diameter. Calculate the hydrostatic force F Am acting on the plug and its center of pressure. 8m 1.2 m 3. The gate as shown is 3 m normal to the page. It keeps the two liquids from mixing with each onough clocuro botween the oil and
4. A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25KN. Determine the vertical force required to lit the gate when its upper edge is 6m below the free water surface and coefficient of friction between the gate and guides is 0.15. Determine the center of pressure acting on the gate. Water 6 m Gate- F-
A closed cylindrical tank 2m in diameter and 8m deep with axis vertical contains 6m deep of oil (sp. Gr = 0.8). The air above the liquid surface has a pressure of 0.8kg/cm². Determine the total normal force acting on the wall at its location from the bottom of the tank.
There is a circular gate at the end of the tank as illustrated. A 6.387 * 10–3 m³ wood block is tied to the end of the gate as illustrated. Density of the wood block is 0.6 g/cm³. Water is at 15.6 °C and Mercury is at 20 °C. What will be the reading h approximately on the mercury manometer on the left side when the gate opens up? Water 50 Wood Hinge 0.4 m Gate D=4 cm Mercury O a. 0.1 m O b.0.14 m c. 0.22 m d. 0.26 m
An a tank filled with mercury (density 13000 kg/m3)at depth 10 m , the force actining at the hatch with diameter 0.75 m (located at the bottom tank) is (Taken gravitational acceleration as 10 m/s2):
Determine the location of the total hydrostatic force from thr bottom surface and the top surface acting on the 2m x 4m gate shown on the illustration.
An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !
Consider a 6 m diameter spherical gate holding a body of water whose height equal to the diameter of the gate. Atmospheric pressure acts on both sides of the gate. The horizontal component of the hydro static force in kN acting on this curved surface is (With Free Body Diagram)
A vessel cylindrical in shape and closed at the top and bottom is 300 mm in diameter, 1 m long and contains water up to a depth of 0.8 m. The air above the water surface is at a pressure of 60 kN/m2 . If the vessel is rotated at a speed of 250 r.p.m. about its vertical axis find the pressure head at the bottom of the vessel (i) At the centre, and (ii) At the edge
Q 3 :A plate ABCD hangs in water from one of its comers (as shown in the figure). Determine the total pressure on the plate and the position of the center pressure? Water Surface 10 m 5m 7 B 612 C _5 m O
The Curves face of el dam, reteining weter, is shaped accordinge to the elationship 2=206 as shown. The dam has a borizon e62 ontal length H0=3m and the height of water reteined the dam is 20=7-3.1The fluid is water. Yweter=9800 N/m and cetmosphenc pressure may be omitted-com pute the resultant force on the dam and its line of action. The width of the dam s 15.3m. The centroid of the Shaded area (Figure Zii) is 不 weiter 2=2 figure 2ii figure 2i